manualshive.com logo in svg

Fayat Group 897, Operation & Maintenance Manual, Page: 278 / 590

Share
Download
Fayat Group 897 Operation & Maintenance Manual Download Page 278

D 31 16

Batteries

The batteries (1) of the 24 V system are
located in the vehicle footwell.

A

For the specifications, refer to chapter B,
”Technical Data”. For maintenance, see
chapter "F".

m

External starting only according to the
instructions (see section "Starting the
paver finisher, external starting (starting
aid)")

Main battery switch

The main battery switch separates the
current circuit from the battery to the
main fuse. 

A

For the assignment of all fuses, see
chapter F

- To interrupt the battery's current cir-

cuit, turn the key pin (3)

 

to the left and

pull it out. 

A

Do not lose the key pin as in this case
the paver finisher can no longer be
moved!

1

3

3

Summary of Contents for 897















































































































































































































































































































































































































































































































































































































Reviews:

No comments