manualshive.com logo in svg

Fastwel CPC308, User Manual, Page: 37 / 81

Share
Download
Fastwel CPC308 User Manual Download Page 37

СРС308 Processor Module

 

 

The Module Structure and Functioning

 

C P C 3 0 8   U s e r   M a n u a l                                                                                          

© 2 0 1 3     F a s t w e l     V e r . 0 0 1 b   E

 

 

37

 

Table 3

-

10: The Designation of the Gigabit Ethernet (XP11) Connector Contacts 

 

When making an interface cable for connecting to the XP11 (IDC10) connector, it is recommended 
to use the ACS00040-04 additional accessory (see Table 1 3). 

3.4.7 

SerialATA Interface 

There are standard SATA interface connectors (XP7 and XP10) located on the CPC308 module 
board. The maximum transmission rate is 300 MB/s. 

Fig. 3-16: SATA Connectors (XP7 and XP10) 

 

Table 3

-

11: The Designation of SATA Connectors (XP7 and XP10) Contacts 

Contact Number 

Function 

1 

GND 

2 

TXP 

3 

TXN 

4 

GND 

5 

RXN 

6 

RXP 

7 

GND 

 

It  recommended  to  use  cables  whose  length  does  not  exceed  45  cm  in  order  to  connect  SATA 
devices. 

 

Attention! 

Connecting  and  disconnecting  standard  SATA  devices  when  the  module  is 
switched  on  may  result  in  the  module  or  power  supply  breakdown. 

It  is 

permitted to connect and disconnect standard SATA devices only when 
the module is switched off!

 

Summary of Contents for CPC308


















































































Reviews:

No comments