manualshive.com logo in svg

Fastfame 9W AP Series, User Manual

Share
Download
Fastfame 9W AP Series User Manual Download Page 26

9W

▄

AP/P + Serial User’s Manual

 

3-19 

IrDA connector (refer to section 2.3 "Connectors"). The HPSIR setting 
allows infrared serial communication at a maximum baud rate of115K 
baud. 

FIR - Select this setting if you installed an Infrared module via IrDA connector 

(refer to section 2.3 "Connectors"). This FIR (Fast IR) setting allows infrared 
serial communication at a maximum baud rate of 4M baud. 

Normal - Sets serial port 2 to operate in normal mode. This is the 

default setting. 

The choice: Normal,SCR,IrDA,ASKIR. 

 

UR2 Duplex Mode 

This item is used to select UR2 Duplex Mode. 
The Choice: Half, Full 
 

Onboard Parallel Port 

This item controls the onboard parallel port address and interrupt.

 

The choice: 378/IRQ7, 278/IRQ5,3BC/IRQ7, Disable. 
 

Parallel Port Mode 

This item lets you set the parallel port mode. The mode options are SPP 
(Standard and Bidirection Parallel Port), EPP (Enhanced Parallel Port) and ECP 
(Extended Parallel Port). SPP is the IBM AT and PS/2 compatible mode. EPP 
enhances the parallel port throughput by directly writing/reading data to/from 
parallel port without latch. ECP supports DMA and RLE (Run Length Encoded) 
compression and decompression. 
The choice: SPP, EPP, ECP,ECP+EPP. 
 

ECP Mode Use DMA 

This item lets you set the DMA channel of ECP mode.

 

The Choice:1,3. 
 

PWRON After PWR Fail 

A traditional ATX system should remain at power off stage when AC power 
resumes from power failure. This design is inconvenient for a network server or 
workstation, without an UPS, that needs to keep power-on. This item is used to 
solve this problem. Selecting On lets the system can automatically power-on after 
AC power resumes; in the other hand, the system will power-off if you select Off. If 
Former-Sts option is selected, the system will power-on or power-off based on the 
original state. 
The Choice: off, on, Former-sts. 

9W

▄

AP/P + Serial User’s Manual

 

3-20 

 

Game Port Address 

This item is used to assign an address for the Game port.

 

The Choice: Disable, 201, 209. 
 

Midi Port Address 

This item is used to assign an address for the MIDI port.

 

The Choice: 330, 300, Disable. 
 

Midi Port IRQ 

This item is used to assign an IRQ for the MIDI port.

 

The Choice:10, 5. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 9W AP Series










































Reviews:

No comments

Brands by name

Popular brands

Load more brands