background image

V.

 

04

2013

 

Opera

 

A - Firs

 

A
p

p

 

Step 1

 
 

Turn the 

clockwise
power le

 

A
c

 
 

 

 
 

 
 

 
 

 
 

3

 

ation 

t time o

Attention
please en

pag.6) 

1 – SK45

 emergency

e to unlock

d is lighted

Attention
connected

Fast &

operation

n! Before 

nsure the 

50 / SK5

 

 

y stop 

: the 

d-ON. 

n! To prev

d to eithe

 

& Fluid Mana

operating

 frame lo

550 pow

 

Unlock
of the 

machi
power

plugge
The po

The m
machi

the int
Please
should

the ma
switch

one w
conne

vent dama

er 220-24

agement B.V

g your SK

ock was c

wer mana

k the emerg

 machine b

ne is autom

r connector

ed into a 22

ower led lig

machine is in

ne from its

terface but

e note that 

d be no rea

achine. In 

hed off (e.g

way of achie

ctor at the 

age, the S

40V/16A/

V. – SK450 / S

K450 / SK

orrectly r

agemen

gency stop

by turning c

matically sw

r at the rea

20-240V w

ghted-ON. 

n stand-by 

s sleeping m

ttons. 

 during nor

son ever to

case the sh

. for maint

eving this: u

 back of the

SK450 / 

/50Hz po

SK550 

K550 for t

removed 

 button on 

clockwise. T

witched on 

r of the sha

all socket. 

 modus. To

modus, pres

mal operat

o take the p

haker must 

enance) th

unplug the 

e machine.

SK550 m

ower grid

the first t

 (as indic

 the front 

The 

when the 

aker is 

o awake the

ss any of 

tion there 

power off 

t be 

here is only 

 power 

 

may only b

ds. 

P9

time, 

cated in 

 

be 

9

 

Summary of Contents for SK450






















Reviews: