manualshive.com logo in svg

Faro FaroArm Fusion, Manual, Page: 46 / 130

Share
Download
Faro FaroArm Fusion Manual Download Page 46

FaroArm

®

 Manual

January 2009

38

Chapter 1: Introduction to the FaroArm

®

2 Digitize the white area of the Calibration Plate with the Laser Line 

Probe in a sweeping motion. You should collect at least 200 scan lines 
in the Laser Line Probe calibration. If not, repeat the calibration 
moving the Laser Line Probe slower in each step. 

• Aim the laser line at the middle of the white surface.

• Move the Laser Line Probe until the laser is in the Center 

Range.

.

• Press the FRONT button and move the Laser Line Probe while 

pointing to the center of the white surface. Rotate the Laser Line 
probe as much as possible - at least 90 degrees. 

• Press the BACK button.

3 Digitize the White area of the Calibration Plate with the Laser Line 

Probe in a sweeping motion. You should collect at least 200 scan lines 
in the Laser Line Probe calibration. If not, repeat the calibration 
moving the Laser Line Probe slower in each step.

• Rotate the Laser Line Probe 90°.

• Aim the laser line at the middle of the white surface.

• Move the Laser Line Probe until the laser is in the Center 

Range.

.

• Press the FRONT button and move the Laser Line Probe while 

pointing to the center of the white surface. Rotate the Laser Line 
probe as much as possible - at least 90 degrees. 

• Press the BACK button.

08M46E00_FaroArmUSB.book  Page 38  Tuesday, February 17, 2009  1:42 PM

Summary of Contents for FaroArm Fusion



































































































































Reviews:

No comments