manualshive.com logo in svg

Faro FaroArm Fusion, Manual, Page: 38 / 130

Share
Download
Faro FaroArm Fusion Manual Download Page 38

FaroArm

®

 Manual

January 2009

30

Chapter 1: Introduction to the FaroArm

®

Holding the Laser Line Probe

Never grab the Laser Line Probe while measuring. Simply hold the 
FaroArm's pistol grip. Holding the Laser Line Probe can cause 
inaccuracy due to bending of its mounting bracket. 

N

OTE

: Avoid touching both lenses. Clean the top and bottom lenses 

with the cloth from the Laser Line Probe case. Dirt and grease on 
either lens can cause poor results.

Hardware Controls and Indicators

The FaroArm/FARO Laser Line Probe system uses the FRONT (Green) 
and BACK (Red) and two LEDs on the back of the Laser Line Probe. 

Buttons

Use the FRONT (green) button to start data collection. Points are only 
sent to the computer when the laser is in range. Once you start collecting 
data, press the FRONT button again to pause.

Use the BACK (red) button to end any measurement command.

Figure 1-28 Holding the FARO Laser Line Probe

08M46E00_FaroArmUSB.book  Page 30  Tuesday, February 17, 2009  1:42 PM

Summary of Contents for FaroArm Fusion



































































































































Reviews:

No comments