Faro FaroArm Fusion Manual Download Page 19

Page: 19 / 130

FaroArm

Manual

January 2009

Chapter 1: Introduction to the FaroArm

OTE

: If the platform specific Bluetooth Wizard finds two COM

ports, usually labeled “Incoming” and “Outgoing,” for the FaroArm,
use the Outgoing COM port.

Computer to the FaroArm Driver Connection

The FaroArm USB driver connects to the SPP connection using the
FARO Bluetooth Connection Setup utility software.

• Start FARO Bluetooth Connection Setup utility software program.

• Click the NEW button.

• Type a name for your connection

• In the P

ORT

list select the proper COM from the platform specific

Bluetooth Wizard (e.g. COM10). This is the port that you previously
wrote down.

• Click the OK button.

A test is automatically run to verify that the COM port is connected to
the FaroArm.

• Enter the FaroArm PIN security code,

faro

• Click OK to save the connection.

Figure 1-10 Connecting the FaroArm to the Computer

Figure 1-11 Connection Name and COM port

Figure 1-12 FaroArm Bluetooth PIN

08M46E00_FaroArmUSB.book Page 11 Tuesday, February 17, 2009 1:42 PM

Summary of Contents for FaroArm Fusion



































































































































Search results

Summary of Contents for FaroArm Fusion

Reviews:

Faro FaroArm Fusion, Manual, Page: 19 / 130

Search results

Summary of Contents for FaroArm Fusion

Reviews: