FarmTek GrowSpan Gothic Pro 106314D Page 36 Assembly Instructions Manual Download

Page: 36 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

17. Repeat the above steps until all cords are attached to

the first curtain panel along one side of the shelter.

Diagram shows cords attached to the curtain conduit

and to the axle. Dashed line shows the position of the

curtain conduit. Roof panels are not show for clarity.

18. Continue by attaching the lower curtain edge to the

baseboard for the first curtain installation.

Cord

Complete these steps to attach the lower edge of the

curtain to the customer-supplied baseboard.

CAUTION:

Do not attempt to attach the curtain to the

baseboard during stormy or windy conditions or when

such conditions are expected.

1. Using the supplied-crank handle, roll the curtain panel

up to within 2" of where it will seat into the channel

created by the ribbon boards.

Attach Lower Edge of the Curtain to Baseboard

After tying all cords to the curtain and axle conduits for the

first curtain assembly, secure the free edge (bottom) of the

curtain panel to the baseboard.

Use customer-supplied dimension lumber as a retaining

board for the lower edge of the curtain. The retaining board

must be at least 1" x 2" to adequately secure the curtain to

the baseboard. See the diagram below for an example.

Diagram may show a different frame and curtain assembly.

INSTALL THE DROP-DOWN CURTAIN (continued)

Panel Pocket with Conduit

2. Move to the bottom of the panel and with assistance,

evenly stretch the panel end-to-end along the

baseboard.

3. Take the first section of customer-supplied retaining

board and place it against the curtain and the

baseboard to hold the curtain in position.

NOTE:

Evenly and gently pull the curtain edge down to

remove wrinkles.

Applying too much force will bend the

curtain conduit.

4. Using the supplied FA4652 fasteners, secure the

retaining board to the baseboard as shown.

5. Repeat the steps to secure the remaining lower edge of

the curtain to the baseboard along the side.

6. Return to the gearbox and check the operation of the

drop-down curtain panel using the crank handle. Adjust

cords as needed for a level curtain.

7. Repeat the steps to attach the remaining curtain to the

other side of the building.

8. Install the anti-billow rope.

End Panel of Shelter

Curtain

Panel

Ground Level

Baseboard and

Retaining Board

Outside View

Retaining Board

Curtain Panel

End Panel of Shelter

Lower Edge of

Curtain Panel

Space FA4652

screws at 24" m/l

Outside View

Rafter

Cord secured

to Axle

Curtain Conduit

in Curtain

Pocket

1" x 4" Board

2" x 6" Board

Summary of Contents for GrowSpan Gothic Pro 106314D






















































Search results

Summary of Contents for GrowSpan Gothic Pro 106314D

Reviews:

Related manuals for GrowSpan Gothic Pro 106314D

Brands by name

Popular brands

FarmTek GrowSpan Gothic Pro 106314D, Assembly Instructions Manual

Search results

Summary of Contents for GrowSpan Gothic Pro 106314D

Reviews:

Related manuals for GrowSpan Gothic Pro 106314D

Brands by name

Popular brands