3
GROWSPAN
™
GOTHIC PRO GREENHOUSES AND SYSTEMS
Revision date: 05.29.19
•
Band Clamp:
Clamp used to connect the end wall
framing to the rafter pipe. In some cases, band
clamps are also used to connect diagonal struts to the
assembled frame.
•
Clip or Fabric Clip:
A short, half-section piece of
conduit (cut lengthwise) used to secure the end panel
cover to the leg or rafter assembly. The clip or fabric
clip is typically fastened in place using self tapping Tek
screw.
•
Conduit:
An assembly of pipes used to secure the
main cover and end panels (if equipped). Purlins
and some strut assemblies also consist of connected
pipes to form a conduit. Each pipe joint of a conduit
assembly is secured with a self-tapping Tek screw to
prevent separation. Some conduit assemblies are used
to secure larger end panels and main covers. These
conduits typically consist of sections of PVC tubing
glued at the joints.
•
Cross Connector:
Any one of the metal brackets
used to "connect" or secure a purlin to a rafter. Cross-
connectors are typically pictured on the Pictorial Parts
Guide page or in the Quick Start section (if present).
•
End Panel:
Fabric or material used to cover the end
wall assemblies. End wall assemblies are optional for
many shelters.
•
Must Read Document:
This document includes
building and shelter anchoring instructions, steps for
end wall reinforcement, safety precautions, and notices
and warnings. The Must Read document is sent with
all shelters and buildings. If you did not receive a Must
Read document, contact Customer Service to request
one.
•
On-Center:
Term used to describe a measurement
taken from the vertical center of the rafter or frame
member to the vertical center of another.
•
Purlin:
The pipe assembly that runs perpendicular to
the rafters or framework that supports the main cover.
Purlins are found on the sides and roof areas of the
assembled frame, are evenly spaced, and typically run
from the front to the back of the shelter.
•
Plain or Straight Pipe:
A term used to describe a pipe
that has the same diameter or width throughout its
entire length.
•
Strut:
A strut is usually a length of pipe with two
flattened ends and is used for diagonal bracing of the
shelter frame. A strut is typically secured to the frame
work by special brackets and bolts.
•
Swaged End or Swaged Pipe:
The term “swaged''
refers to the tapered end of the pipe or tube. Swaged
ends of a pipe can be inserted into couplers and the
straight ends of other pipes.
•
Tek Screw:
A self-tapping fastener used to secure pipe
joints and to fasten brackets to rafters.
ASSEMBLY PROCEDURE
Following the instructions as presented will help ensure
the proper assembly of your greenhouse. Failing to follow
these steps may result in an improperly assembled and
anchored greenhouse and will void all warranty and
protection the owner is entitled.
The steps outlining the assembly process are as follows:
1. Verify that all parts are included in the shipment. Notify
Customer Service for questions or concerns.
2. Read these instructions, the Must Read document, and
all additional documentation included with the shipment
before
you begin assembling the greenhouse.
3. Gather the tools, bracing, ladders (and lifts), and
assistance needed to assemble the greenhouse.
4. Check the weather
before
you install the roof cover
and any panels (if equipped). Do not install covers or
panels on a windy or stormy day.
5. Re-evaluate the location and site based on the
information and precautions presented in the
documentation included with the shipment.
6. Prepare the site (if applicable).
7. Assemble the frame components in the order they are
presented in these instructions.
8. Assemble the frame including the struts (if equipped).
9. Consult the MUST READ document and properly
anchor the assembled frame.
10. Install the End Wall framing. (These are optional items
for some shelter types.)
11. Install, tighten, and secure the End Wall end panels
and doors. (These are optional items for some
shelters.)
12. Install, tighten, and secure the main cover. This applies
to fabric and film covers that stretch over the frame
assembly.
13. Attach the curtain components to the main frame,
install the curtain, and attach the anti-billow ropes.
14. Read the care and maintenance information at the end
of these instructions.
15. Complete and return all warranty information as
instructed.
LIST OF WORDS AND PHRASES
Before you begin, it is important to become familiar with the
words and phrases used in this instruction manual. These
words and phrases are common to most GrowSpan™
shelters and identify the different parts of the shelter.
(Some are used in this document. Others may not apply to
this particular shelter.) These terms describe the shipped
parts and can also be found on the materials list/spec
sheets included with the shipment. To aid in the assembly,
read through the following definitions before you begin to
assemble your shelter.
