background image

OPERATING MANUAL  

OILSEED SCREW PRESS FARMET DUO

 

Page 

13

 of 

48

 

 

 

 

by a person: 

 

Authorised by the Owner  

 

Educated in the machinery field with knowledge of repairs of similar 
equipment  

 

Demonstrably acquainted with safety regulations for work with the 
Equipment 

A.4

 The Operator must secure the safety of other persons when working with the 

Equipment.  

A.5

 The Operator may only enter the Equipment  structure when the Equipment 

is in standstill and only for the following reasons: 

 

Adjustment of the working parts of the Equipment  

 

Repair and maintenance of the Equipment 

A.6

 Any changes or modifications of the Equipment may only be performed with 

written  consent  of  the  Producer.  The  Producer  bears  no  liability  for  any  potential 
damage  incurred  due  to  the  failure  to  observe  this  instruction.  All  warning  and 
safety  signs  must  be  legible  and  in  their  places.  In  case  of  damage  or  loss,  these 
signs must be immediately renewed. 

A.7

  The  Operator  must  have  the  Operating  Manual  with  the  work  safety 

requirements available at any time when working with the Equipment. 

A.8

  The  Operator  must  not  consume  alcohol,  medicines,  narcotic  and 

hallucinogenic substances  that reduce attention and coordination capabilities while 
using the Equipment. If the Operator must use medicines prescribed by a physician 
or uses over-the-counter medicines, he must be informed by a physician, whether he 
is  capable  of  a  responsible  and  safe  operation  of  the  Equipment  under  such 
circumstances. 

A.9

  The  Equipment  may  be  activated  provided  that  it  is  technically  fit  and 

complies  with  regulations  for  safety  and  hygiene  at  work  and  provided  that  it  is 
used in compliance with the terms and conditions specified by the Producer.  

A.10

  When  working  with  the  Equipment,  follow  the  instructions  in  this 

Operating  Manual  as  well  as  generally  binding  regulations  for  safety  at  work, 
protection of health, fire and traffic safety and protection of the environment.  

A.11

  Do  not  use  water  to  extinguish  fire  of  electric  equipment.  In  case  of  fire, 

follow the valid fire regulations.  

 

 

Summary of Contents for DUO

















































Reviews: