Farmet DISKOMAT 6,5 PSW Operating Manual Download

Page: 39 / 44

MACHINE MAINTENANCE AND REPAIRS

11.2 Machine lubrication shedule

•

During machine maintenance and its lubrication, it is necessary to observe the safety regulations.

LUBRICATION POINT

INTERVAL

LUBRICANT

Tow bar joint

Daily, always before the work

with the machine.

Always after the end of the

season and before storing the

machine

Plastic grease

KP2P-20 Likx

DIN 51 502

Lubricant handling:

•

Protect yourselves against direct contact with oils by using gloves or protective creams.

•

Thoroughly wash oil spots on the skin using warm water and soap.

•

Do not clean the skin with petrol, engine diesel fuel or other solvents.

•

Oil is poisonous. If you swallowed the oil, immediately seek a physician.

•

Protect the lubricants against children.

Summary of Contents for DISKOMAT 6,5 PSW













































Search results

Summary of Contents for DISKOMAT 6,5 PSW

Reviews:

Related manuals for DISKOMAT 6,5 PSW

Brands by name

Popular brands

Farmet DISKOMAT 6,5 PSW, Operating Manual

Search results

Summary of Contents for DISKOMAT 6,5 PSW

Reviews:

Related manuals for DISKOMAT 6,5 PSW

Brands by name

Popular brands