Farm King 13114 Operator And Parts Manual Download

Page: 134 / 268

Operation - 13" Backsaver Auger

134

With the main auger in the fully down position, move

the auger towards the bin or barn. Position the auger

as close as possible to the bin or barn.

Stop the tractor and engage the parking brake. Engage

the tractor’s hydraulics. Run the tractor engine at low

idle.

Figure 291

Using the tractor controls, slowly raise the main auger

to the desired height (do not exceed a 42° angle).

Back the auger into position above the bin. Lower the

auger until the downspout (Item 1)

[Figure 291]

enters

the bin.
Engage the tractor’s parking brake, stop the engine

and exit the tractor.

Unloading Belly Dump Units

Figure 292

Move the hopper (Item 1)

[Figure 292]

out at a 90°

angle from the auger.
Move the belly dump unit into position, centered on

the hopper

[Figure 292]

Mark the path of the belly dump unit for future units

to unload and maintain the proper distance from the

auger to allow adequate space for the hopper to be

moved in and out without interference.
Move the hopper mover lever left or right to move the

hopper in towards the auger, away from vehicle

traffic.

Figure 293

Move the belly dump unit straight forward until

centered on the intake auger pivot. Stop the belly

dump unit.
Move the hopper (Item 1)

[Figure 293]

under the belly

dump unit.

Never place blocks under the wheels to increase the

elevation of auger.

1395 OP

Keep wheels of undercarriage level and on firm

ground. Raise the auger to the desired height and

back the auger into position. Do not support the

auger on the bin. As the auger becomes full, the

weight may cause damage to the underside of the

auger or to the bin.

B-0534

B-0537

Summary of Contents for 13114













































































































































































































































































Search results

Summary of Contents for 13114

Reviews:

Related manuals for 13114

Brands by name

Popular brands

Farm King 13114, Operator And Parts Manual

Search results

Summary of Contents for 13114

Reviews:

Related manuals for 13114

Brands by name

Popular brands