background image

 

This system has been carefully designed to be as effective as possible. 
There are some occasions, however, on which it cannot provide accurate 
detection. The operation of any kind of alarm system can be intentionally 
impeded or fail for other reasons, such as the following: 
 

 

Improper installation. A security system must be properly 

installed to provide appropriate protection. This device should 
not be placed in locations where it could be exposed to humidity 
or liquid from water sprinklers. Each installation must be 
evaluated to ensure that all areas are covered. 

 

It is very important that the security system is serviced 

periodically to ensure that it is in proper working order and 
parts must be updated or replaced if they are not providing the 
expected protection. 

 

Power cuts. NEXHO-IC requires an appropriate energy supply for 

proper operation. If the device is working on batteries, it is 
possible that they will fail. Even if the batteries do not fail, 
please make sure that they are in good condition and are 
installed properly. If the device is running on an external power 
supply, any outage, even of short duration, will interrupt the 
operation during the power cut. Power cuts of any duration are 
often accompanied by voltage fluctuations which can damage the 
device. Following a power outage, please perform a complete 
check of the system to ensure that it is working properly. 

 

Discharged batteries. The lifetime of a battery depends on the 

environment in which it is found and on the number of 
activations of the device. Environmental conditions such as 
excessive humidity, high or low temperatures or abrupt 
temperature changes can reduce the lifetime of the battery. 
Regular inspections and maintenance will keep the system in 
good operational condition. 

 

Sound alarm devices may not be heard by hearing-impaired 

people. 

Warning 

Summary of Contents for NEXNO-IC

















Reviews: