Mi 2472
14
I
T
ALIANO
E
NGLISH
F
RANÇAIS
E
S
P
AÑOL
P
ORTUGUÊS
D
EUTSCH
LCD
The contrast and the background colour of the display can
be changed as follows:
-
access the programming mode as described in the sec-
tion “Enter the programming mode”;
-
select “LCD” and press
, the display shows
Backlighting
and Contrast.
-
Backlighting
To change the background colour of the screen, you must:
-
select “
Backlighting
” and press
;
-
use the buttons
to change the colour and press
to
confirm
.
- Contrast
To change the contrast of the screen, you must:
-
select “Contrast” and press
, a horizontal bar indicating
the current contrast value is shown
;
- u
se the buttons
to change it and press
.
Miscellaneous
Inside, you can enable or disable the following functions:
-
Key X for PWD
. Using the button
(instead of 00+
) to
shorten the procedure required to enable the coded lock
and access the programming mode (Example: press +
Pa
).
- YES enables the button for this function.
- NO remains disabled.
-
Extended PWD
. Allows the activation of all user pass-
words increasing their number from 20 to 250.
- YES enables 250 passwords.
- NO enables 20 passwords.
-
Disable tone.
Enable/disable keypad tones.
- Yes disables all keypad tones.
- NO enables all the tones.
To access the programming mode, you must:
-
access the programming mode as described in the sec-
tion “Enter the programming mode”;
-
select “
Misc.
” and press
;
the display shows:
Key for
PWD, Extended PWD and Disable tone;
- s
elect one of them by pressing
and press
;
- c
hoose YES or NO with
and press
to confirm;
- c
ontinue with other programming or return to the list of
programming by pressing .
Default.
To restore the keypad setting made at the factory and then
delete all changes made during programming you must:
-
select “
Default
” and press
;
the display shows
No and
Yes;
- p
ress No not to delete the programming made, press Yes
to restore the default settings and delete the recently ones
made.
Version.
Inform about the software version of the keyboard.
Restoring the Administrator Password.
If you lose the administrator password you can reset the
factory one assigned by default (0039) as follows:
-
cut the power supply to the keyboard;
- simultaneously press the buttons 1, 3 and 0;
- restore voltage to the keyboard and hold pressed the
buttons 1, 3 and 0 until the message “Default Admin.
Password” is displayed;
- release the buttons; now the password 0039 is restored.
OPERATION
Check that all connections are correct. Connect the power
supply unit to the mains; the push-button panel automatically
checks the status of the line displaying for 5 seconds
“TD6100PL / Release.....”; at the end of checking, in case of
failure, the display shows “ERROR.....” in case of a positive
check on the display appears the message “Press
to
select the number" alternating with "Press
to call the user".
Dial the number or select the desired user name (if previ-
ously stored) by pressing the or buttons, once the
desired user name appears on the display press the
to
make a call.
In case of error press (only before sending the call) and
dial the correct to number.
If the line is free, you will hear a confirmation tone and the
display shows “Call in progress---“; the extension rings for
the number of times defined by programming “Ringtone -
Number of rings”.
If press the call is terminated and the system is ready for
a new call.
The called user picks up the handset enables the
conversation with the external station for 60 seconds. The
display shows “Connection ---- ”.
The display of the door station starts flashing 10 seconds
before conversation ends. To continue conversation for
additional 60 seconds press
again (up to 3 times).
From the internal station, press the
button to release
the door lock; this operation requires that the user is in
conversation and wait about 1 second after lifting the hand-
set. The lock release activation time is defined by program-
ming "S1-S2" (page 13).
Replace the handset or press on the door station to
restore the idle state.
Numbers that are not sent or deleted go off after 25 seconds.
In installations with 2 or more main push-button panels,
when a call is made from one push-button panel, the other
push-button panels are deactivated with the busy signal.
Wait until the line is free to make the call.
Door lock opening
The door lock can be opened from the push-button panel,
including in “busy” mode, by dialling one of the 4-digit
passwords you have entered.
