manualshive.com logo in svg

Fanvil i23S, User Manual, Page: 7 / 52

Share
Download
Fanvil i23S User Manual Download Page 7

7 / 52

www.fanvil.com

Network/SIP 

Registration

Network error: Blink with 1s

Network running: Off

Registration failed: Blink with 3s

Registration succeeded: On

B.Start Using

Before you start to use the equipment, please make the following installation.

1. Confirm the connection

Confirm whether the equipment of the power cord, network cable, electric lock control line 

connection and the boot-up is normal. (Check the network state of light)

Power, Electric Lock, Indoor switch port

There are 2 power supply options: 12V/DC or POE (Powered By Ethernet).    PIN 1 (+12V) 

and PIN 2 (VSS) connected to the power supply. PIN3/4/5 used to connect the electric lock, only 

2 of them (NC and COM, or NO and COM) will be connected usually, depending on the type of 

electric lock. PIN6/7 used to connect indoor switch which control the open/lock of electric lock.

CN7

1

2

3

4

5

6

7

+12V

VSS

NC

COM

NO

S_IN

S_OUT

12V 1A/DC

Electric-lock switch

Indoor switch

Driving mode of electric-lock(Default in Passive mode)

Driving mode of electric-lock decides whether the electric-lock use an independent power supply. 

The independent power supply will be required in passive mode, while electric-lock will be 

powered by i31S in active mode.

Ǐ

Note

ǐ

When the device is in active mode, it can drive 12V/650mA switch output maximum, to 

which a standard electric-lock or another compatible electrical appliance can be connected.

z

When using the active mode, it is 12V DC in output.

z

When using the passive mode, output is short control (normally open mode or normally close 

mode).

Jumper in passive mode 

   

Jumper in active mode 

Summary of Contents for i23S





















































Reviews:

No comments