background image

27 / 52

www.fanvil.com

Activate

Whether the service of the line should be activated

SIP Proxy Server 

Address

Enter the IP or FQDN address of the SIP proxy server

SIP Proxy Server Port

Enter the SIP proxy server port, default is 5060

Outbound proxy 

address

Enter the IP or FQDN address of outbound proxy server which are

provided by the service provider

Outbound proxy port

Enter the outbound proxy port, default is 5060

Realm

Enter the SIP domain if requested by the service provider

Codecs Settings

Set the priority and availability of the codecs by adding or removing them from the list.

Advanced Settings

Subscribe For Voice 

Message

Enable the device to subscribe a voice message of waiting notification, if it 

is enabled, the device will receive notification from the server when there 

is voice message waiting on the server

Voice Message 

Number

Set the number for retrieving voice message

Voice Message 

Subscribe Period

Set the interval of voice message notification subscription

Enable DND

Enable Do-not-disturb, any incoming call to this line will be rejected 

automatically

Blocking Anonymous 

Call

Reject any incoming call without presenting caller ID

Use 182 Response for 

Call waiting

Set the device to use 182 response code at call waiting response

Anonymous Call 

Standard

Set the standard to be used for anonymous

Dial Without 

Registered

Set call out by proxy without registration

Click To Talk

Set Click To Talk

User Agent

Set the user agent, the default is Model with Software Version.

Response Single 

Codec

If setting is enabled, the device will use single codec in responding to an 

incoming call request

Ring Type

Set the ring tone type for the line

Conference Type

Set the type of call conference, Local=set up call conference by the device 

itself, maximum supports two remote parties, Server=set up call 

conference by dialing to a conference room on the server

Server Conference 

Number

Set the conference room number when conference type is set to be 

Server

Transfer Timeout

Set the timeout of call transfer process.

Summary of Contents for i23S





















































Reviews: