manualshive.com logo in svg

Fanvil FV6030, User Manual

Share
Download
Fanvil FV6030 User Manual Download Page 57

                                                       
 

- 57 -

 

Outside Port 

Set the WAN port of the NAT mapping 

Notice:

 After finish setting, click the Add button to add new mapping table; click the Delete 

button to delete the selected mapping table. 

Shows the outside WAN port IP address and the inside LAN port IP address. 

Outside IP 

Set the outside Wan port IP address of DMZ. 

Inside IP 

Set the inside LAN port IP address of DMZ 

Click the 

Add 

button to add new table; click the 

Delete 

button to delete the selected mapping 

table. 

Notice:

  10M/100M adaptive means the network card, and other equipment physical consultations 

speed, testing speed under bridge mode near to 100M, in order to ensure the quality of voice and 

communications real-time performance, we made some sacrifices of NAT under the transmission 

performance. T

ransmit with full capability only when system is idle

, so can not guarantee 

that the transmission speed reach to 100M. 

 

 
4.3.6.4. VPN Config 

This web page provides us a safe connect mode by which we can make remote access to enterprise 

inner network from public network. That is to say, you can set it to connect public networks in 

different areas into inner network via a special tunnel.   

 

Summary of Contents for FV6030































































Reviews:

No comments

Brands by name

Popular brands

Load more brands