Fanvil FV6030 User Manual Download | Manualshive

Page: 49 / 62

background image

- 49 -

Config Setting

Field name

explanation

Save Config

you can save all changes of configurations. Click the Save button,

all changes of configuration will be saved, and be effective

immediately. .

Backup Config

Right clicks on “Right click here…” and select “Save Target As….”

then you will save the config file in .txt format

Clear Config

user can restore factory default configuration and reboot the phone.

If you login as Admin, the phone will reset all configurations and

restore factory default; if you login as Guest, the phone will reset

all configurations except for VoIP accounts (SIP1-5 and IAX2) and

version number.

4.3.5.4. Update

You can update your configuration with your config file in this web page.

«
...
47
48
49
50
51
...
»

Summary of Contents for FV6030































































Reviews:

No comments

Related manuals for FV6030

Brand: Damall Pages: 7

Brand: 2N Pages: 32

Brand: H-TEK Pages: 142

StarPoint 500 Entry

Brand: 2N Pages: 59

Brand: Blu Pages: 21

Brand: DMP Electronics Pages: 4

Brand: Tadiran Telecom Pages: 222

Brand: SMART Pages: 16

Brand: FAMOCO Pages: 19

Brand: HTC Pages: 4

Brand: Alcatel Pages: 2

CLEARSOUND ClearText

Brand: Geemarc Pages: 31

Brand: NEC Pages: 187

Brand: AEG Pages: 32

Brand: AEG Pages: 106

Brand: AEG Pages: 122

Brand: AEG Pages: 144

Brand: AEG Pages: 227

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands