11.
Battery must not be charged in temperatures below freezing or above
12.
To extend the battery’s lifespan:
a.
Avoid draining the battery
dives even when the LED Indicator starts rapidly flashing
unit to a charger at this point.
b.
During long periods of storage, the unit should be stored partially charged in a cool and
dry area.
Moisture Detector
The Moisture Detector allows monitoring the watertight seal of the housing during the dive. Moisture
detectors are very sensitive, so whenever moisture is detected by the sensor, the LED Indicator
flashing red and a warning alarm starts beeping, thereby alerting of a possible leak.
1.
You can test the Moisture Detector (image
#23) by placing a wet finger over
moisture sensor unit at the bottom of the
housing.
2.
In order to silence the alarm after it starts
beeping:
a.
Gently wipe the Moisture Sensor unit
with a soft dry cloth in order to dry it off.
b.
Switch the Vacuum System off using the power switch on the Signal Board.
3.
Never soak or wash the interior of the housing with water. T
to all Hybrid Vacuum Safety System electronic components!
Installing the Vacuum Valve
1.
Remove the M16 Cap from the M16 port by screwing it all the way out. Store it in a secure place for
possible future use.
2.
Install the Vacuum Valve by screwing it inside the dedicated M16 port at the back of the housing.
Carefully tighten the Vacuum Valve by fitting the wrench around the edges of its base and gently
!
Hybrid Vacuum System instructions provided in the sections below refer only to
housings which
a Vacuum Valve is installed on and made use of
FRX100 VA R Housing Instruction Manual
26
y must not be charged in temperatures below freezing or above 50°C (122°F)
To extend the battery’s lifespan:
battery all the way to 0%. Even though the unit can handle a few more
dives even when the LED Indicator starts rapidly flashing blue, it is best to connect the
unit to a charger at this point.
During long periods of storage, the unit should be stored partially charged in a cool and
The Moisture Detector allows monitoring the watertight seal of the housing during the dive. Moisture
detectors are very sensitive, so whenever moisture is detected by the sensor, the LED Indicator
flashing red and a warning alarm starts beeping, thereby alerting of a possible leak.
Moisture Detector (image
placing a wet finger over the
at the bottom of the
nce the alarm after it starts
ipe the Moisture Sensor unit
with a soft dry cloth in order to dry it off.
Switch the Vacuum System off using the power switch on the Signal Board.
Never soak or wash the interior of the housing with water. This will cause irreparable damage
to all Hybrid Vacuum Safety System electronic components!
Remove the M16 Cap from the M16 port by screwing it all the way out. Store it in a secure place for
Install the Vacuum Valve by screwing it inside the dedicated M16 port at the back of the housing.
acuum Valve by fitting the wrench around the edges of its base and gently
Hybrid Vacuum System instructions provided in the sections below refer only to
a Vacuum Valve is installed on and made use of
Instruction Manual 20200225
50°C (122°F).
. Even though the unit can handle a few more
blue, it is best to connect the
During long periods of storage, the unit should be stored partially charged in a cool and
The Moisture Detector allows monitoring the watertight seal of the housing during the dive. Moisture
detectors are very sensitive, so whenever moisture is detected by the sensor, the LED Indicator starts
Switch the Vacuum System off using the power switch on the Signal Board.
his will cause irreparable damage
Remove the M16 Cap from the M16 port by screwing it all the way out. Store it in a secure place for
Install the Vacuum Valve by screwing it inside the dedicated M16 port at the back of the housing.
acuum Valve by fitting the wrench around the edges of its base and gently
Hybrid Vacuum System instructions provided in the sections below refer only to
a Vacuum Valve is installed on and made use of.
Image #23
