Falcon TA Series Page 3 Installation Instructions Manual Download

Page: 3 / 10

Install inside spring cage assembly

Fully tighten mounting screws.
Lever catch faces door edge.

Lever catch

Door edge

Inside

TA291, TA501 shown

Install inside rose

5a Align the indent on the rose with the upper notch on the

spring cage.

Notch

Indent

TA291, TA501 shown

5b Place the indent on the notch with the opposite side of the

rose angled slightly away from the spring cage as shown.
Then, press the other side of the rose into place.
You should hear a click as the rose is pressed into place.

Indent on rose

engaged with

notch

Press here

Install inside lever

FOR FUNCTIONS TA101, TA291, TA301, TA501, TA511, TA571,

AND TA581 ONLY:

Push the inside lever onto the spindle.
Be sure to engage the lever catch.

Lever catch

TA291, TA501, TA571 shown

For TA381 function see page 5,

for TA561 see page 6, or

for TA575 see page 7

for inside of lock

installation steps.

Summary of Contents for TA Series











Search results

Summary of Contents for TA Series

Reviews:

Related manuals for TA Series

Brands by name

Popular brands

Falcon TA Series, Installation Instructions Manual

Search results

Summary of Contents for TA Series

Reviews:

Related manuals for TA Series

Brands by name

Popular brands