Falcon TA Series Installation Instructions Manual Download | Manualshive

Page: 6 / 10

background image

6

TA561 Classroom Function ONLY

See other functions on previous and following pages.

1. Install strike, latch and chassis/outside spring cage assembly as shown in steps 1 through 5.

2. Adjust the inside hub position using the timing tool:

TA561 Function ONLY

Rotate inside hub with timing tool

clockwise until it stops.
Then, rotate counterclockwise

approximately 180 degrees

until opening is horizontal.

Inside

3. Install the dummy cylinder.

4. Push the inside lever onto the spindle.

Be sure to engage the lever catch.

Lever catch

«
...
4
5
6
7
8
...
»

Summary of Contents for TA Series











Reviews:

No comments

Related manuals for TA Series

Brand: Wano Pages: 4

Brand: C.R. Laurence Pages: 2

Mansion iLock X2

Brand: Oji Pages: 20

Brand: Yale Pages: 2

Brand: ATIENA Pages: 11

87D2S10006 Series

Brand: Richelieu Pages: 4

Brand: JNF Pages: 2

VISTA PIVOT II 1505D-48

Brand: Sterling Plumbing Pages: 3

Brand: Sterling Plumbing Pages: 16

LokkLatch Round

Brand: D&D Technologies Pages: 2

Lokk-Latch PRO-SL

Brand: D&D Technologies Pages: 2

Stock Locks C8052

Brand: COMPX Pages: 1

Brand: Kaba Pages: 2

SAFETRON 5000 Series

Brand: SAFE TRON Pages: 24

Brand: Abloy Pages: 12

Brand: IFAM Pages: 5

Brand: iglooworks Pages: 29

Brand: Dormakaba Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands