background image

E3901i / E3902i 
Induction Boiling Tables

INSTALLATION and 
SERVICING INSTRUCTIONS

IMPORTANT

The installer must ensure that the installation of the appliance is in conformity with these instructions
and National Regulations in force at the time of installation. Particular attention MUST be paid to –

BS7671 IEE Wiring Regulations
Health and Safety At Work Act
Electricity at Work Regulations
Fire Precautions Act

WARNING

READ THESE INSTRUCTIONS BEFORE INSTALLING THIS APPLIANCE.

BEFORE ATTEMPTING ANY MAINTENANCE, ISOLATE THE APPLIANCE AT THE MAINS
ISOLATING SWITCH AND TAKE STEPS TO ENSURE THAT IT CANNOT BE INADVERTENTLY
SWITCHED ON.

IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BEFORE INSTALLING
AND COMMISSIONING THIS APPLIANCE. FAILURE TO COMPLY WITH THE SPECIFIED
PROCEDURES MAY RESULT IN DAMAGE AND NEED FOR A SERVICE CALL.

On completion of the installation these instructions should be left with the Engineer-in-Charge for
reference during servicing. In addition, the Users Instructions should be handed to the User, having
had a demonstration of the operation and cleaning of the appliance.  

PREVENTATIVE MAINTENANCE CONTRACT

In order to maintain maximum performance from this unit we would recommend that a Maintenance
Contract be arranged with 

SERVICELINE

. Regular visits can be arranged to adjust, maintain and

repair the unit. A quotation will be given upon request to the contact numbers below.

WEEE Directive Registration No. WEE/DC0059TT/PRO

At end of unit life, dispose of appliance and any replacement 
parts in a safe manner, via a licenced waste handler.
Units are designed to be dismantled easily and recycling of all 
material is encouraged whenever practicable.

Falcon Foodservice Equipment

HEAD OFFICE AND WORKS

Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland.

SERVICELINE CONTACT

Phone: 01438 363 000

Fax: 01438 369 900

T100803 Ref. 3

Summary of Contents for E3901i











Reviews: