SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
29
d) Fit replacement control and re-assemble parts in
reverse order.
9
To Remove a Hotplate Tap
a) Remove the hotplate as detailed in Section 2.
b) Remove the control panel as detailed in Section 3.
c) Unplug the FSD lead from the rear of the tap. Undo
compression fitting at the rear of the tap. Remove the
fixings that secure the tap to the gas rail. Disconnect
the ignition switch wiring.
d) Remove the tap. Remove and discard the gasket seal.
Fit new gasket seal to replacement tap.
e) Re-assemble in reverse order. Check the appliance is
gas sound. Check hotplate ignition.
10 To Change an Ignition Switch
Change the gas tap as detailed in Section 9.
11 To Remove a Hotplate Burner Injector
a) Remove the hotplate as detailed in Section 2.
b) Remove the injector directly from the burner body.
c) Fit the appropriate injector.
d) Re-assemble in reverse order. Check the appliance is
gas sound.
12 To Remove a Hotplate Burner Spark Electrode
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Undo the bezel venturi and remove the bezel from the
hotplate. The spark ignition wire will be pulled through
the electrode clearance hole.
c) Disconnect the spark electrode from the ignition wire.
Note
Take care to prevent the ignition wire from falling back
through the clearance hole.
d) Undo the spark electrode from the bezel by removing
the spring clip and spring.
e) Fit the replacement electrode to the burner bezel.
Ensure that the spring and clip are properly located.
When re-fitting the electrode lead, ensure that the
black insulation sleeve is pushed over the electrode.
f) Replace in reverse order and check correct burner
ignition.
13 To Remove a Hotplate Burner
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Remove the hotplate as detailed in Section 2.
c) Remove the nut that secures the burner body to the
support channel.
d) Remove the fixings that secure the support channel to
the chassis. Lift the channel clear of the appliance.
e) Undo the compression fitting which connects the
burner body to the gas pipe. Remove the burner body
from the appliance.
f) Replace in reverse order. Check the appliance is gas
sound and that the burner operates satisfactorily.
14 To Remove the Oven Door
a) Open the oven door.
b) Support the door and remove the two screws which
secure the upper hinge to the front frame of the unit.
c) Remove the door from the lower hinge by lifting
slightly and moving it outward.
d) Re-assemble in reverse order.
15 To Remove the Grill Door
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Remove the hotplate as detailed in Section 2.
c) Remove the control panel as detailed in Section 3
d) Remove LH side panel a detailed in Section 4.
e) Remove the kicker plate (4 screws).
f) Remove the central vertical cover situated between
the ovens. (5 screws).
g) Remove the 2 countersunk screws (1 per side) which
secure the hinge arms to the front of the grill chamber.
Note
The door hinge arms are spring tensioned. Carefully
remove the grill door and retain the gaskets.
h) Re-assemble in reverse order. Ensure that the gasket is
fitted between the hinge arm and the front of the grill
chamber. Check door operation.
16 To Remove the Oven Outer Door Panel
a) Open the oven door.
b) Remove two screws ‘A’ and two screws ‘B’ from the
door.
c) Remove the outer door panel.
d) Undo the nuts that secure the handle to the door
panel. Fit the handle to the replacement door panel.
e) Fit the replacement panel to the oven inner door.
f) Re-assemble in reverse order.
17 To Remove the Door Latch
a) Remove the oven outer door panel as detailed in
Section 16.
b) Remove the fixings that secure the latch assembly to
the inner door panel.
c) Fit the replacement catch and re-assemble in reverse
order.
d) Check correct operation of door.
