Fala STROKKUR-1, Manual

Page: 10 / 48

10
GB
O R I G I N A L I N S T R U C T I O N S
with a wrench because it is made of plastic and can be destroyed by applying too much force.
Attention! Before connecting the product to a hydraulic installation, you should make sure, that the water supply has been shut
down.
You should fasten the water inlet with a nut and gasket, using, for example. the flexible hose (V).
Make sure, that heater valve is in its closed position (VI) and opens the water supply to the heater. Make sure, that water supply
shows no traces of the leaks and open the heater valve, by turning the valve up or down. The water should outflow from the spout
outlet. Check whether the sprout connection and the heater are showing any traces of leaks.
If you detect any leaks, you should close the water supply to the heater, and then remove the cause of the leaks and again check
the tightness of connections.
After the tightness confirmation of water connections, you may connect the heater to the electrical power supply.
Make sure, that the battery valve is closed, and that the outlet spout is not producing any water, then insert the plug of the power
cable to the mains socket. Open the heater valve by turning it up, the water outlet should produce hot water. At the same time, the
control lamp will turn on at the body of the heater, which means starting the heating element operation.
USE OF THE PRODUCT
Attention! The heater can produce water at very high temperature, higher than the normal operating temperature of hot water in
the water supply. You should exercise caution, to avoid burning up during the heater operation.
The degree of valve opening regulates the intensity of the water stream. The more the valve is opened, the lever is closer to the
extreme position, the more intense the water flow is produced from the outlet spout. However, because it is easier to heat less
intense stream of water, the more intense is the stream, the lower is the water temperature.
The heating element switches on automatically when you open the heater valve and rotate it up. The heating element switches off
automatically when you close the valve. In the case when the valve is turned down the heater does not start.
Attention! When you do not use the battery for an extended period of time, you should disconnect it from the electrical power
supply. Remove the plug from the mains socket.
MAINTENANCE OF THE PRODUCT
Attention! All maintenance operations must be carried out when the heater power supply is turned off. You should unplug the
charger from the mains outlet.
Heater body, sprout, and other parts, which are made of plastic, should be cleaned using a soft cloth and the cleaning products,
which are intended for the maintenance of plastic. After the cleaning, you should wipe the heater body with a soft cloth soaked in
water, and then dry or let it for drying.
Chrome-plated parts should be cleaned like plastic parts, but with the use of appropriate cleaning agents.
It is forbidden to use aggressive detergents for the product maintenance. It is forbidden to use any abrasive agents, as well as
cleaning agents, which are containing alcohol, acids (except for the 2% solution of vinegar with water) and solvents.
Water supplied to the mixer faucet must be cleaned from all mechanical and chemical impurities. The manufacturer accepts no
responsibility for mixer faucet damages due to contamination of water.
If, however, the intensity of the water stream will be reduced It may be due to the clogging of water inlet to the battery or water
outlet from the spout.
Attention! Before the start of the following maintenance activities, you should close the water supply to the heater.
In order to clear the battery water inlet you should unscrew the heater body from its base, remove the gasket, and then carefully
remove the flange, which is fixing the strainer, and then the same strainer (VII). Clean all elements with a stream of running water
and install them in reverse order to their disassembly. Perform a leak test of water connections before connecting the product to
the power supply.
In order to ensure patency of the water outlet of spout, you should unscrew the aerator (VIII) and check its patency. Check the
condition of the gasket and, if necessary, clean up both elements with a stream of running water. Then mount the gasket and screw
the aerator without the use of tools. Perform a leak test of water connections before connecting the product to the power supply.