background image

TALOS 9450

TALOS 9450/HRC

TALOS

 

9460

TALOS

 

9460/HRC

TALOS 9470

TALOS 9470/HRC

TALOS 9480

TALOS 9480/HRC

4
4
4
4
4
4
4
4

500
500
600
600
700
700
800
800

TALOS 9651

TALOS 9651/HRC

TALOS

 

9661

TALOS 9661/HRC

TALOS 9671

TALOS 9671/HRC

TALOS 9681

TALOS 9681/HRC

12
12
12
12
12
12
12
12

500
500
600
600
700
700
800
800

Meccanica Fadini s.n.c.

Responsible Manager

DECLARATION OF CONFORMITY:

Meccanica Fadini snc (Via Mantova, 177/A - 37053 Cerea - VR - Italy) declares under its own responsibility that TALOS  is in 
compliance with the Directive 2006/42/EC on machinery, moreover: is to be sold and installed as a comprehensive 
“Automatic System”, including the accessories and components as recommended by the Manufacturing Company. In 
observance of the current directives, any automation is to be regarded as a “machine”. Therefore it is required that all the 
applicable safety normsare strictly complied with by installation agents, who are also required to issue a Declaration of 
Conformity. The manufacturing company is not liable for incorrect applications or misuse of its products that are declared 
to be produced in compliance with the following norms: Analysis of the risk and actions to cure them EN 12445 & EN 12453, 
Low Voltage Directive 2014/35/UE, Electro-magnetic Compatibility Directive 2014/30/UE. In order to certify the product 
the Manufacturer declares under his own responsibility the compliance with the PRODUCT regulations under the NORMS 
EN 13241-1.

GENERAL DESCRIPTION OF THE PRODUCT

Talos is a bollard  fitted with a fully retractable post  sinking flat to the ground level. It is an oil-hydraulic system, the movements of 
which are  by an incorporated motor-pump. It is designed to  securely stop traffic from an area.
The TALOS series includes a vast selection of options as indicated below, varying in height, thickness and depth of embedding 
(constraint) for impact resistance (the abbreviation HRC identifies those bollards having higher ratings of resistance to crash and 
impact than the standard versions).
The construction features and installation procedure are the same across the entire range:

The retractable post, 275 mm diameter, is made of S235J steel (4 mm thickness) and S355J steel (12 mm thickness), cataphoresis 
treated and polyester powder coating.
A stainless steel version is avialable, INOX Aisi 304 satin finish, but only in the 4 mm thickness option.
In the 

HRC 

options, the post (raised) stays embedded into the casing 40 cm (constraint) deeper rather than 20 cm as with the 

standard versions, thus ensuring higher resistance to impact and crash.
The electronic controller Elpro S40 is to be installed externally, in a sheltered place.
A wide range of safety and control accessories make this bollard easy and safe to operate and therefore suitable to any 
applications, either in public or private areas.
Any TALOS can be  completed with supplementary accessories, to be specified at the time of the order as required (pre-assembled 
and pre-wired to the internal terminal block):

Solenoid valve

: it allows the post to lower in case of power failure.

Presence sensor (pressure switch)

: it prevents the post from rising in case an obstacle stays on it. 

-

 Beeper

: an acoustic device  operating during the rising and lowering movements of the post.

-

 Heating resistor: 

a device used to keep Talos warm inside when the external environment is below 5 °C.

model

320.000
420.000
320.000
420.000 
320.000
420.000
320.000
420.000

stroke

[mm]

stroke

[mm]

crash

 resistance

[J]

model

crash

 resistance

[J]

post 

thickness

[mm]

post 

thickness

[mm]

450.000
550.000
450.000
550.000 
450.000
550.000
450.000
550.000

Retractable Oil-hydraulic Bollard

English

3

Summary of Contents for TALOS Series





















Reviews: