fadini Strabuc 918, Instruction Manual

Page: 16 / 16

- 32 -
GB
Strabuc 918 and Strabuc 930 Strabuc 918 and Strabuc 930
Strabuc 918 Strabuc 918
Strabuc 930 Strabuc 930
Strabuc 930 Heavy Armoured Strabuc 930 Heavy Armoured
700
920
ø 100
1.620
10
700
700
10
920
1.620
1.035
325
1.010
25
10
ø 275
thickness 4 mm
ø 325
thickness 6 mm
ø 450 ø 450
ø 462
ø 405
≠ 40x10
ø 80
ø 345
ø 425
ø 100
ø 275
thickness 12 mm
ø 275
ø 325
thickness 6 mm
ø 425
10 metres long each 10 metres long each
ORDINARY MAINTENANCE AND WASTE DISPOSAL
For optimal performance of the system over time and operation in compliance with safety regulations, correct maintenance and checks must be
performed on the operator, the electronic equipment constituting the installation and on wiring performed.
The entire installation should be carried out by authorized technicians, who are also to fill in the Maintenance Form as indicated in the Norms Book
(available on request):
1° - Oil-hydraulic operator: maintenance check every 6 months.
2° - Electronic equipment and safety systems: a monthly maintenance check.
3° - Ordinary and extraordinary maintenance to be agreed upon between end user/contractor and installation agent.
4° -
Packaging materials such as cardboard, nylon, polystyrene, etc. should be disposed of using specialised waste collection firms.
IF THE OPERATOR IS REMOVED
1° - Disconnect the main switch before opening the lid of the electric cable junction box.
2° -
Do not cut the electric wires , rather remove them from the terminal board loosening the clamping screws inside the dividing box.
Via Mantova, 177/A - 37053 Cerea (VR) Italy
Tel.+39 0442 330422 - Fax +39 0442 331054
e-mail: info@fadini.net - www.fadini.net
The manufacturer reserves the right to make amendments to this manual without priornotice and declines all responsibility for any errors, personal injury or damage to property.
ELECTRIC MOTOR
Power output 0,25 kW (0,33 HP)
Power consumption 330 W
Power supply voltage 230 V
Frequency 50 Hz
Absorbed current 1,8 ÷ 3,5 A (6 A max)
Motor rotation speed 2.800 rpm
Intermittent service S3
CYLINDRICAL CONTAINER - to be cemented
Material "FE" sheet steel
Treatment Hot dip galvanization
Calandered sheet metal thickness 1,5 mm
Fixing flange thickness 10 mm
4x support plates flat 40x10
Total weight 30 kg
Strabuc 918 Strabuc 918
Post diameter Ø 275 mm
Post thickness 4 mm
Post height 700 mm
Plunger diameter 30 mm
Rod diameter 16 mm
Net rod travel 740 mm
Calibrated thrust 18 daN
Frequency of use very intensive
Rising time ~ 6,1 s
Lowering time ~ 5,7 s
Protection class - Strabuc 918 IP 67
LED power supply 230 V - 50 Hz
LED lights 24 V
Post finishing Powder coating polyester
RAL 1028 - Melon yellow
Post material “FE 360” steel
Stainless Steel/Inox version “AISI 304”
Impact resistance 40.000 J
Crash resistance 280.000 J
Maximum static load 20.000 kg
Complete weight of Strabuc 918 140 kg
OIL-HYDRAULIC MAIN UNIT
Hydraulic pump P10
Pump flow rate 4,45 litres/1’
Operating pressure 2 MPa (20 bar)
Max pressure 3 MPa (30 bar)
Operating temperature - 20 °C + 80 °C
Oil container capacity 1,5 litres
Oil type Oil Fadini - code 708L
Protection class IP 67 (IP 65 with electrovalve)
Strabuc 930 - Strabuc 930 Strabuc 930 - Strabuc 930 Heavy Armoured Heavy Armoured
Post diameter Ø 275 mm
Post thickness 12 mm
Post height 700 mm
Plunger diameter 30 mm
Rod diameter 16 mm
Net rod travel 740 mm
Calibrated thrust 18 daN
Frequency of use very intensive
Rising time ~ 11,6 s
Lowering time ~ 9,9 s
Protection class - Strabuc 930 IP 67
LED power supply 230 V - 50 Hz
LED lights 24 V
Post finishing Powder coating polyester
RAL 7016 - Anthracite gray
Post material “FE 360” steel
Impact resistance 45.000 J
Impact resistance 410.000 J
Maximum static load 20.000 kg
Complete weight of Strabuc 930 180 kg
2019/04
GB
2012/19/UE Directive
Re. disposal of electric
and electronic waste
DISPOSE PROPERLY OF MATERIALS
ARMFUL TO THE ENVIRONMENT