Fabtech FT22176i Installation Instructions Manual Download Page 17

- Product Warranty and Warnings -

Fabtech provides a Limited Lifetime Warranty to the original retail purchaser who owns the vehicle, on which the product was 
originally installed, for defects in workmanship and materials.

The Limited Lifetime Warranty excludes the following Fabtech items; bushings, bump stops, ball joints, tie rod ends, limiting 
straps, cross shafts, heim joints and driveshafts. These parts are subject to wear and are not considered defective when worn. 
They are warranted for 60 days from the date of purchase for defects in workmanship.

Dirt Logic and Performance Coilover take apart shocks are considered a serviceable shock with a one year warranty on leakage 
only. Service seal kits are available separately for future maintenance. All other shocks are covered under our Limited Lifetime 
Warranty.

Fabtech does not warrant any product for finish, alterations, modifications and/or installation contrary to Fabtech’s instructions. 
Alterations to the finish of the parts including but not limited to painting, powder coating, plating and/or welding will void all 
warranties. Some finish damage may occur to parts during shipping, which is considered normal and is not covered under 
warranty.

Fabtech products are not designed nor intended to be installed on vehicles used in race applications or for racing purposes or 
for similar activities. (A “RACE” is defined as any contest between two or more vehicles, or any contest of one or more vehicle 
against the clock, whether or not such contest is for a prize). This warranty does not include coverage for police or taxi vehicles, 
race vehicles, or vehicles used for government or commercial purposes. Also excluded from this warranty are sales outside of 
the United States of America.

Installation of most suspension products will raise the center of gravity of the vehicle and will cause the vehicle to handle 
differently than stock. It may increase the vehicle’s susceptibility to a rollover, on road and off road, at all speeds. Extreme care 
should be taken to operate the vehicle safely at all times to prevent rollover or loss of control resulting in serious injury or death. 
Fabtech front end Desert Guards may impair the deployment or operation of vehicles equipped with supplemental restraining 
systems/air bag systems and should not be installed if the vehicle is equipped as so.

Fabtech makes every effort to ensure suspension product compatibility with all vehicles listed on the website, but due 
to unknown auto manufacturer’s production changes and/or inconstancies by the auto manufacturer, Fabtech cannot be 
responsible for 100% compatibility, including the fitment of tire and wheel sizes listed. The Tire and Wheel sizes listed in 
Fabtech’s website are only a guideline for street driving with noted fender trimming. Fabtech is not responsible for damages 
to the vehicle’s body or tires. Fabtech is not responsible for premature wear of factory components due to the installation of 
oversized tires and wheels.

Fabtech’s obligation under this warranty is limited to the repair or replacement, at Fabtech option, of the defective product only. 
All costs of removal, installation or re-installation, freight charges, incidental or consequential damages are expressly excluded 
from this warranty. Fabtech is not responsible for damages and/or warranty of other vehicle parts related or non related to the 
installed Fabtech product. This warranty is expressly in lieu of all other warranties expressed or implied. This warranty shall not 
apply to any product that has been subject to accident, negligence, alteration, abuse or misuse as determined by Fabtech.

Fabtech suspension components must be installed as a complete system including shocks as shown on our website. All 
warranties will become void if Fabtech parts are combined and/or substituted with other aftermarket suspension products. 
Combination and/or substitution of other aftermarket suspension parts may cause premature wear and/or product failure 
resulting in an accident causing injury or death. Fabtech does not warrant products not manufactured by Fabtech.

Depending on the condition of the factory suspension components retained after the installation of a Fabtech suspension not 
all vehicles may have the same ride stance front to rear as described in the website. The blue color of suspension components 
shown in all Fabtech photographs are for display purposes only. Majority of all Fabtech components will be black specifically 
where noted with part numbers ending in BK.

Installation of Fabtech product may void the vehicles factory warranty; it is the consumer’s responsibility to check with their 
local vehicle’s dealer for warranty disposition before the installation of the product. Some state laws may prohibit modification of 
suspension to a vehicle in whole or in part. It is the responsibility of the installer and consumer to consult local laws prior to the 
installation of any Fabtech suspension product to comply with such written laws.

It is the responsibility of the distributor and/or the retailer to review all warranties and warnings of Fabtech products with the 
consumer prior to purchase.

Fabtech reserves the right to super cede, discontinue, change the design, finish, part number and/or application of parts when 
deemed necessary without written notice. Fabtech is not responsible for misprints or typographical errors within the website or 
price sheet. For the most recent Product Warranty and Warnings visit our website www.fabtechmotorsports.com

Instruction Sheet Part# -

 FT22176i 

 REV. AK 07/13/15

17 of 17

Summary of Contents for FT22176i


















Reviews: