background image

                                                                                                                                              

6 < 

<

 

<

 

<

 

 

 

 

Table 2 

 
IT IS  NOT ALLOWED  to burn  waste,  fine  chipping,  bark,  wood  handled with  preventive  chemicals, 
furthermore paper and cardboard. For kindling please use wood scrapings or grill starter but never 
use liquid auxiliaries! 
First kindling 

 

Before installation, remove the securing element used for transportation from the baffle plate 
over the combustion space (Picture 6).

 

Warning! Upon the first kindling, smoke and unpleasant smell may be generated. Always ensure the 
proper ventilation of the room (by opening windows and doors), and heat the fireplace at maximum 
rated heating performance. If with the first heating the maximum temperature is not reached, the 
above-mentioned effects may as well arise later on. 
 
 

 

Open  the  door  by  raising  the  handle  (picture  no.  2).  If  the  equipment  is  hot,  you  can  use 
insulated gloves.  

 

Open the primary air regulator (picture no. 3). 

 

Put light wood or wood scrapings onto the fire-grate. First put small pieces of wood then bigger 
ones on it, light them and close the door again. If the wood burns quickly and leaves sufficient 
glowing embers, put further fuel on it. Following that, set the primary air regulator (picture no. 
3) and the fuel separating according to the table on page 20.  

The  first  kindling  should  be  performed  “finely”  with  little  fuel  only,  so  that  the  parts  of  the 
fireplace  are  adapted  to  heat.  During  the  first  kindling,  the  generation  of  smell  is  normal  and 
absolutely un dangerous. 
 

3.2

 

Putting out of operation 

 

Let the glowing ember burn to ashes and the fire-place get cold. 

 

Empty the furnace chamber and the ash bin. 

 

Close the doors and push the primary air regulator totally to the left. 

 

3.3

 

Heating instructions  

Fire-places  with  closed  furnace  chamber  have  self-locking  furnace  chamber  doors.  These  shall  be 
opened only for kindling, loading or when cleaning the furnace chamber (otherwise problems with 
draught can occur at other equipment leading to the same chimney).   
Warning! 
When opening the furnace chamber door, any incorrect handling or insufficient draught may induce 
smoke.  Always  ensure  that  the  furnace  chamber  door  may  be  opened  only  slowly,  first  just  to  a 
small extent, and then fully after a few seconds. In addition, if You intend to put additional fuel 
into  the  fire,  before  the  opening  of  the  door  only  there  may  be  only  ember  bed  in  the  burning 
space, i.e. no flames may be visible. 
Led  into  the  burning  space  in  correspondence  with  the  existing  conditions,  the  secondary  air 
provides for the follow-up burning of the combustible components of in the burning space. This in 
fact means smoke and soot-poor burning, which contributes to the protection of the environment. If 
you  wish  to  commission  the  fireplace  in  a  transitional  period,  please,  please  first  examine  the 
chimney  draught,  as  it  can  be  especially  weak  at  high  external  temperatures.    Towards  this  end, 
hold a burning match in the slightly opened feeding door. If the flame is not drawn significantly by 
the draught, then a so-called starting fire is to be set first. Towards this end, burn wood chips/wool 
in the fireplace or the cleaning hole of the chimney. The fire grate is to be cleaned before every 
kindling  to  ensure  the  proper  inflow  of  air  for  burning.  The  ashtray  is  to  be  emptied  regularly 
(Picture 4). Should the equipment be extremely hot, use the gloves provided. Please, be careful not 
to dispose glowing materials into the waste bin.  
Ensure that the ashtray should be fully pushed into the equipment. 
 

Warning! 

In order  to  keep  the  air clean  and safeguard  the  fireplace,  do  not  exceed  the  specified 

maximum  fuel  quantity;  otherwise  overheating  may  occur,  which  potentially  damage  the 
equipment. Such damage is not covered with any guarantee. Only a single layer of fuel is allowable 
to  be  prepared  in  the  fireplace.  Try  to  reach  lower  heating  performance  only  by  decreasing  the 
quantity of fuel, and not by cutting the primary air supply. 

Summary of Contents for Oscar
















Reviews: