Version 09/12- Page 9
Cleaning
The mesh grease filters should be cleaned frequently in hot
detergent solution or washed in the dishwasher. Stainless steel
cleaner should be used on stainless rangehoods. Abrasives
and scouring agents can scratch stainless steel finishes and
should not be used to clean finished surfaces.
Replacing the Lamps
Purchase halogen bulb - (Max 20W, 12V, type MR11 bulb
with glass lens)
Before attempting to replace the lamps, make sure that the
light switch is turned off,
USE CAUTION AS THE BULB MAY
BE HOT
. . Remove the 2 screws
(as indicated in FIGURE
16)
that hold the light support and gently pull the support down
from the hood. Remove the lamp from the light support and
replace with new lamp. Replace the light support and fix it
into place with the 2 screws.
An alternative method to replace the lamps is to use a 1
1/4" suction cup (
FIGURE 17
). Attach the suction cup to
the bulb and pull firmly down on the bulb and replace with
a new lamp.
This rangehood system is designed to remove smoke, cooking
vapors and odors from the cooktop area.
For Best Results
Start the rangehood several minutes before cooking to develop proper
airflow. Allow the unit to operate for several minutes after cooking is
complete to clear all smoke and odors from the kitchen.
FIGURE 17
WIRING DIAGRAM
I
Schema Elettrico
NL
Schema Electrisch
GB
Electric Diagram
E
Esquema Eléctrico
F
Schéma Electrique
Esquema Eléctrico
D
Schema Elektrisch
I
Schema Elettrico
NL
Schema Electrisch
GB
Electric Diagram
E
Esquema Eléctrico
F
Schéma Electrique
Esquema Eléctrico
D
Schema Elektrisch
PT
PT
436003384 SF5_023 r-
436003384 SF5_023 r-
• This rangehood uses 20 watt halogen lamps.
USE AND CARE CONTINUED
Grease Filter and Charcoal Filter Alarm Reset
When "FF" message appears on the LED screen, the metal
grease filters need to be washed in the dishwasher (
SEE FIGURE
15
for removal instructions). To reset the metal grease filter alarm
and the charcoal filter saturation alarm, turn off the motor and lights.
Next, press and hold the 24 hour button "E" until the filter message
disappears.
Charcoal Filter Information
The charcoal filters should be replaced (as indicated in FIGURE
5 on page 6) when the "EF" message appears on the LED screen
or at least every 4 - 6 months depending on heavy usage. The
alarm only comes on when the motor is turned on.
Charcoal Filter Alarm Activation
The filter alarm has to be activated in order to use with ductless
installations which use the charcoal filters. The alarm can be
activated upon installation or at a later time. To activate or deactivate
the alarm turn off the motor and lights, and disconnect
the hood from the power source. Press and hold the "B" button
and while holding down the "B" button, reconnect the power
source. Two rotating rectangles will then show on the LED screen
and within 3 seconds press and hold the "B" button LED screen
shows a confirmation of the chosen setting below:
"EF" flashes twice - Charcoal filter saturation alarm ENABLED
"EF" flashes once - Charcoal filter saturation alarm DISABLED
Repeat the process if you want to change the chosen setting, ie if
the filter alarm is disabled, repeat the above paragraph to enable.
Once finished with the activation / de-activation, unplug and plug
in again the power source to return to normal hood function.
FIGURE 15
FIGURE 16
Remote Control
The rangehood can be controlled using the optional remote
control
(purchased seperately)
which has the control layout
(indicated in FIGURE 14 on the previous page). The remote
uses alkaline AAA type batteries.To replace the batteries,
remove the cover by removing the
screw and sliding off the cover (as indicated in FIGURE 18).
Do not place the remote control close to heat sources.
FIGURE 18
Summary of Contents for CYLINDRA ISOLA
Page 18: ......
