background image

5

FAAC Model S450H 24V Hydraulic Swing Gate Operator

RESIDENTIAL VEHICULAR GATE OPERATOR CLASS I

A vehicular gate operator system intended for use in a single family dwelling, garage or associated parking area.

UL325 Gate Operator Classifications

COMMERCIAL / GENERAL ACCESS VEHICULAR GATE OPERATOR CLASS II

A vehicular gate operator system intended for use in commercial locations or buildings such as multi-family housing 

units (five or more single family units), hotels, parking garages, retail stores or other buildings that service the general 

public.

INDUSTRIAL / LIMITED ACCESS VEHICULAR GATE OPERATOR CLASS III

A vehicular gate operator system intended for use in industrial locations or buildings such as factories, loading docks 

or other locations not intended to service the general public.

RESTRICTED ACCESS VEHICULAR GATE OPERATOR CLASS IV

A vehicular gate operator system intended for use in guarded industrial locations or buildings such as airport security 

areas or other restricted access locations that do not service the general public, and in which unauthorized access is 

prevented via supervision by security personnel.

This  FAAC swing gate operator is supplied 

with two warning signs to alert people that a 

possible hazard exists and that appropriate 

actions should be taken to avoid the hazard or 

to reduce exposure to it. 
Permanently install one warning sign on each 

side of the gate so they are fully visible to 

traffic and pedestrians.

Use appropriate hardware such as metal 

screws (not supplied) to permanently install 

each warning sign.

Installing the Warning Signs

Summary of Contents for S450H


















Reviews: