background image

4

200

145

2168 / 2768 / 3368

360

ENGLISH

The level of noise emission of operator D1000, referred 

to the work station, is 52 dB(A).

These instructions apply to model 

FAAC D1000

.

The D1000 automated systems make it possible to automate 

balanced sectional doors of single garages for residential 

use.

They consist of an electro-mechanical operator, electronic 

control unit and courtesy light built into a single unit. This unit is 

fitted to the ceiling and opens the door by means of a transmission 

chain or belt.

The system is non-reversing and, therefore, the door locks 

mechanically when the motor is not operating and, consequently, 

no lock is necessary; two manual releases, one on the inside 

and one on the outside (optional) make it possible to move the 

door in case of a power cut or fault.

The operator is supplied with an electronic device that detects 

the presence of an obstacle that would hinder door movement 

-  the device prevents crushing or lifting. 

This instruction refers to the operator with chain drive, but the 

same procedures, regulations and application limits apply also 

to the belt driven operator.

The D1000 automated systems were designed and built for 

indoor use and to control vehicle access. Do not use them for 

any other purpose.

1.  DIMENSIONS 

2. TECHNICAL SPECIFICATIONS

AUTOMATED SYSTEM D1000

3. ANCILLARY ELECTRICAL EQUIPMENT

Prepare the electric system in keeping with the instructions in 

the chapter entitled “Warnings for the installer”.

When you have finished installing, check if any external pipes 

or cables can come into contact with moving parts. 

Install the fixed control points at a minimum height of 150 cm, 

clear of the door movement area, but in a position enabling 

visual control of that area.

  Cable 2 x 0.5 mm

2

 (TX photocell)

 

Cable 4 x 0.5 mm

2

 (RX photocell)

  Power pipe (230V)

  Low voltage pipe

 

Cable 2 x 1.5 mm

2

 (power)

Fig. 2

Dimensions in mm.

Fig. 1

Model

D1000

Power supply (V ~ / 50 Hz.)

230

Electric motor (Vdc)

24

Maximum absorbed power (W)

350

Thrust force (N)

600/1000

Type of use

continuous

Maximum dimensions from ceiling (mm)

35 (Fig. 4)

Courtesy light (V ~/W)

230 / 40 max.

Courtesy light timer (sec)

120

Standard speed with no-load carriage (m/min)

8,9

Slow speed with no-load carriage (m/min)

4,5

Carriage deceleration speed (m/min)

1,1

Noise at standard speed (dB(A))

52

Travel length at deceleration

Varies according to set-up

Intrinsic safety device 

Category 2

Maximum sectional door width (mm)

5000

Maximum sectional door  height (mm)

See useful travel

Sliding guide useful travel (mm)

2500 - 3100 - 3800

Protection class

For indoor use only (IP20)

Operating ambient temperature (°C)

-20 / +55

Summary of Contents for D1000




















Reviews: