1.
DESCRIPTION
The FAAC BILAMP accessory is a luminous signalling device
comprising a white courtesy lamp with 150-second timer
and an intermittent yellow flashing light.
It may be utilised either externally, positioned on pillars or
posts, or internally installed in garages, passageways, etc.
1.1 TECHNICAL SPECIFICATIONS
Table 1: FAAC BILAMP specifications
Supply voltage
230 V~ ( +6% -10%) 50 Hz
Input
50 W
Degree of protection
IP55
Lamp
Miniature ball E27 230V/25W
Max load of lamp
25W
Ambient temperature
-20 °C +55 °C
Terminal block inputs
Power supply / Timer start
Connector
Courtesy lamp
1.2 LAY-OUT
a
a
a
a
a
J1 Terminal block:
Courtesy-lamp power supply and
Start control - see fig.5.
b
b
b
b
b
J2 Terminal block:
Courtesy-lamp power supply, max.
25W.
c
c
c
c
c
Luminous
intermittent signal lamp (FAACLAMP), max.
25W.
2.
BILAMP INSTALLATION
Warning: before carrying out any type of operation on the
FAAC BILAMP luminous signalling device
(connections,
maintenance), always disconnect the electrical power
supply.
1) Determine the installation point of the FAAC BILAMP
luminous device, by checking that the signal lamp is
fully visible from both inside and outside the property.
There are two possible installation solutions:
- Wall positioning (fig.1);
- Floor positioning (fig.2).
The FAAC BILAMP luminous device allows optional fitting
of the receiver (see paragraph 3).
In such case a multicore cable with three .5 mm
2
conductors will be required for the connection of the
receiver.
NB: Do not use the same multicore cable for connecting
the receiver and the luminous signalling device.
However, in order to avoid any electrical disturbance, it
is preferable to use separate sheathing or shielded
cable for connecting the receiver.
2) Secure the support of the device using screws or screw
anchors.
2
1
3
NB: Before carrying out such operation, channel the
electric cable/s into the special hole machined from
the base of the support (fig. 1/2).
3) Prepare the cables for connection to the electronic
board.
Cable diameter should be not less than 1 mm
2
.
In order to facilitate wiring operations, make the cable
trail from the wall (or floor) by about 25cm.
4) Using a Philips screwdriver, remove the yellow and white
covers of the FAAC BILAMP (fig.3).
5) Remove the luminous signal lamps.
6) Remove the diaphragm (A) situated on the opposite
side of the arrow engraved on the body of the luminous
device (fig.4).
7) Effect the wiring on the FAAC BILAMP card and the
electronic board as per fig. 5, respecting the polarity
engraved on the card.
8) Refit everything.
3.
RECEIVER INSTALLATION
The body of the luminous device is designed to allow
optional fitting of a receiver.
In such case, proceed as follows:
1) Pierce the diaphragm as per fig.6.
2) Channel the cable and insert the device into the
support by pressing the two coupling tabs, as per fig. 7.
3) Insert the supplied lower door into the luminous signalling
device, as per fig. 8.
4) Insert the electric cables into the receiver support.
Secure the receiver support using the screws supplied
as shown in fig.8
5) Effect the wiring.
4.
MAINTENANCE
The FAAC LAMP is fitted with two lamps that can be
accessed by removing the respective side cover, (fig. 3).
Replace the faulty component with a similar one, as
detailed by the specifications, table1
The fitting of lamps with a greater rating than that requested
can cause irreparable damage to the electronic circuit
situated inside the FAAC BILAMP luminous signalling device.
7
ENGLISH
ENGLISH
