background image

A7

F

+

+

Advanced Programming: 

To access ADVANCED PROGRAMMING, press and hold key F 
and then press key +:

•  Release key +, the unit displays the name of the first 

function.

•  Release key F, modify the value of the function with keys 

+ and -.

•  Press and hold key F, the unit displays the name of the 

next function, and if you release it, the value that can be 
modified with keys + and -.

•  When you reach the last function, press F to exit the pro-

gram, the unit resumes monitoring input status.

The following table shows the sequence of functions 
accessible in ADVANCED PROGRAMMING:

ADVANCED PROGRAMMING

MAXIMUM TORQUE AT INITIAL THRUST:

The motors operate at maximum torque 

(ignoring the torque setting) at start of 
movement. Useful for heavy leaves.

 = Active 

= Disabled

LAST STROKE AT CLOSING:

The motors are activated at full speed for 1 
second to facilitate locking of the electric lock.

 = Active 

=Disabled

REVERSING STROKE:

Before opening, while the gate is closed, 

the motors thrust to close for 2 seconds thus 
facilitating release of the electric lock.

 = Active 

 = Disabled

LEAF 2 OPENING DELAY (2 s):

Enables delayed start (at opening) of leaf 2, 
avoiding interference between leaves.

 = Active 

 = Disabled

FAIL SAFE:

If this function is activated, it enables a 
function test of the photocells before any 
gate movement. If the test fails (photocells 
not serviceable), the gate does not start the 
movement.

 

= Active 

 = Disabled

PRE-FLASHING (5 s):

Activates the flashing lamp for 5 seconds before 
start of movement.

 = Active 

 = Disabled

ELECTRIC LOCK ON LEAF 2:

For using the electric lock on leaf 2 instead 
of on leaf 1.

 = Active 

 = Disabled

INDICATOR-LIGHT:

If 

is selected, the output functions as a 

standard indicator-light (lighted at opening and 
pause, flashing at closing, and off when gate is 

closed). Different figures correspond to the extra 
time compared to normal work time (opening 

or closing) when the output can be used - via a 
relay - to power a courtesy light. Time can be 
adjusted from   to 

 sec. in 1 sec. steps, 

and from    to 

 min. in 10 sec. steps.

   

= Standard indicator-light

from  to 

 =  Timed output

CLOSING PHOTOCELLS REVERSE AT RELEASE:

Enable this function if you want the closing 
photocells to stop movement and reverse at 

release. Default setting is immediate reverse.

 = Active 

 = Disabled

ASSISTANCE REQUEST (combined with next 
function):

If activated, at the end of countdown (settable 
with the next function i.e. “Cycle programming”) 
it affects 8 s of pre-flashing at every Open 

pulse (job request).  Can be useful for setting 
scheduled maintenance jobs.

 = Active 

 = Disabled

CYCLE PROGRAMMING:

For setting countdown of system operation 
cycles. Settable (in thousands) from   to 
thousand cycles. The displayed value is updated 
as cycles proceed.
This function can be used to check use of the 
board or to exploit the “Assistance request”.

A.D.M.A.P. FUNCTION:

When enabled, the safety devices operate in 

compliance with French standard NFP 25/362.

 = Active 

 = Disabled

Exit from programming and return to inputs 
status monitoring.

NOTE

: Parameter modifications take effect immediately. 

Exit out of programming to save changes. If the equipment 

is powered down before returning to normal status monitor-
ing, any unsaved modifications will be lost.

To restore programming defaults, press and hold the 

three b, -, F simultaneously for 5 seconds.

EXTRA WORK TIME:

If reversing occurs, and if the leaf does not 
reach its end contact point, you can activate 
this function to increase work time.

    = Active 

 

  = Disabled

Display

Function

Default

Display

Function

Default

Summary of Contents for 400































Reviews: