F.u.n.k.e. 800ATC-H-260-260 Operation And Installation Download

Page: 26 / 52

TRT800H / P/N 800ATC-H-(26x)-(26x)

Operation and Installation

Document-No: 03.2126.010.71e / Revision: 1.00

3.8 Antenna

3.8.1 Antenna Selection

•

Recommended antennas: see section 3.11 Accessories

•

Choose an antenna type compatible with the vehicle and the

mounting location.

•

Specified features depend on proper installation of the antenna.

•

The radiation pattern needs to be verified considering aircraft type

and mounting location.

•

The electrical interference between the antenna and any other

equipment must be taken into account in such a way that no
reduction of the performance of any other system will occur.

•

Install only certified antennas!

3.8.2 Installation Recommendation

•

Take note of the antenna manufacturer’s instructions.

•

The usually deployed Dipole- or Blade antennas necessarily

require a high frequency capable solid metal ground plane at the
antenna base.

•

For installation in composite aircrafts, ground planes are to be

added. The ground plane should be as large as possible but in any
case not smaller than 10 cm x 10 cm. If in doubt, please contact
the aircraft manufacturer.

•

Keep away three feet from any other antenna.

•

Pursue mounting in vertical position under the belly in flight

direction.

3.8.3 Antenna Wiring

•

Suitable antenna cables: see section 3.11 Accessories

•

Keep wiring as short as possible.

•

The smallest cable bend radius is 10cm. Avoid sharp bends.

•

Keep away from an ADF antenna cable at least 12 inches.

•

Electrical connections to the antenna shall be protected against

moisture to avoid loss of efficiency.

Summary of Contents for 800ATC-H-260-260





















































Search results

Summary of Contents for 800ATC-H-260-260

Reviews:

Related manuals for 800ATC-H-260-260

Brands by name

Popular brands

F.u.n.k.e. 800ATC-H-260-260, Operation And Installation

Search results

Summary of Contents for 800ATC-H-260-260

Reviews:

Related manuals for 800ATC-H-260-260

Brands by name

Popular brands