F.F. Group SRT 180 EASY, Original Instructions Manual

Page: 9 / 60

PRODUCT SPECIFICATIONS
INTENDED USE
This power tool is intended to function as a grinder,
sander, wire brush, polisher, carving or cut-off tool.
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
TECHNICAL DATA
Article number 45 335
Model SRT 180 EASY
Rated voltage
V 220
Hz 50
Rated power input W 180
No-load speed min
-1
10.000-30.000
Collet capacity mm 2,4/3,2
Weight kg 0,7
Sound emission values determined according
to EN 60745-1, EN 60745-2-23
Typically the A-weighted noise levels of the product
are:
Sound pressure
level
dB(A) 83,0
Sound power level dB(A) 94,0
Uncertainty K dB 3,0
Vibration total values a
h
(triax vector sum)
and uncertainty K determined according to EN
60745-1, EN 60745-2-23
Vibration level max:
a
h
m/s
2
3,13
K m/s
2
1,5
NOISE/VIBRATION INFORMATION
The vibration emission level has been measured
in accordance with a standardized test given in EN
60745-1; it may be used to compare one tool with
another and as a preliminary assessment of ex-
posure to vibration when using the tool for the
applications mentioned.
The vibration emission during actual use of the
power tool can differ from the declared total
value depending on the ways in which the tool is
used. There is the need to identify safety meas -
ures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
WARNING! This machine produces an electro-
magnetic field during operation. This field may
under some circumstances interfere with active
or passive medical implants. To reduce the risk
of serious or fatal injury, we recommend persons
with medical implants to consult their physician
and the medical implant manufacturer before op-
erating this machine.
IDENTIFICATION
1. Collet nut
2. Collet
3. Nose cap
4. Shaft lock button
5. On/Off switch
6. Hanger
7. Ventilation openings
8. Variable speed dial
9. Collet wrench
ACCESSORIES (A)
ALWAYS UNPLUG THE TOOL BEFORE CHANGING
ACCESSORIES
Use only FF Group tested, high performance ac -
cessories. Be sure to read the instructions supplied
with your FF Group accessory for further informa -
tion on its use. Handle and store accessories care -
fully to avoid chipping and cracking.
ƒ
Press the shaft lock button and rotate the shaft
by hand until it engages the shaft lock. Do not en -
gage the shaft lock while the tool is running.
ƒ
With the shaft lock engaged, loosen (do not re -
move) the collet nut. Use the collet wrench if
necessary.
ƒ
Insert the bit or accessory shank fully into the
collet.
ƒ
With the shaft lock engaged, tighten the collet
nut.
USE
GETTING STARTED
The first step in using the multitool is to get the
“feel” of it. Hold it in your hand and feel its weight
and balance. Feel the taper of the housing. This
taper permits the tool to be grasped much like a
pen or pencil.
IMPORTANT! Practice on scrap material first to
see how the tool’s high-speed action performs.
Keep in mind that your multitool will perform best
by allowing the speed, along with the correct FF g-
Group accessory and attachment, to do the work
for you. Do not put pressure on the tool during
use, if possible. Instead, lower the spinning ac -
cessory lightly to the work surface and allow it to
touch the point at which you want to begin. Con -
centrate on guiding the tool over the work using
very little pressure from your hand. Allow the ac -
cessory to do the work. Usually it is better to make
a series of passes with the tool rather than to do
the entire job with one pass. A gentle touch gives
the best control and reduces the chance of error.
HOLDING THE TOOL
Always hold the tool away from your face.
Accessories can be damaged during handling
and can fly apart as they come up to speed.
When holding tool, do not cover the ventila-
tion openings with your hand. Blocking the
English | 9
www.ffgroup-tools.com
SRT 180 EASY