Ezurio BISMS02BI-01 Manual Download Page 9

 

www.ezurio.com 

DSH_BT024-00200_1v4 © Ezurio  Ltd 2006 

RS-232  

Port /TXD @ application sends data to the module’s UART_RX signal line  

Port /RXD @ application receives data from the module’s UART_TX signal line  

 

 

 

 

 

 

 

 

 

 

 

Figure 6.1 : UART interfaces  

Note that the serial module output is at 3.0V CMOS logic levels.  Level conversion must be added to interface with 
an RS-232 level compliant interface. 

 

6.1.2

 

GPIO Port  

Eight lines of programmable bi-directional input/outputs (I/O) are provided that can be accessed either via the 
UART port, or Over The Air (OTA) from a second 

Bluetooth

 unit.  These can be used as data inputs or to control 

external equipment.  By using these in OTA mode, an embedded 

Bluetooth

 Serial module can be used for control 

and data acquisition without the need for any additional host processor. A further line can be used as an input. 

Each of the GPIO ports can be independently configured to be either an Input or Output.  A selection of ports can 
be accessed synchronously. 

The  ports  are  powered  from  V

CC

.  The  mode  of  these  lines  can  be  configured  and  the  lines  are  accessed  via  S 

Registers in the range 623 to 629. 

Low latency I/O can be accessed by using Ezurio’s I/O via an enhanced inquiry process. 

 

6.1.3

 

PCM CODEC Interface 

PCM_OUT, PCM_IN, PCM_CLK and PCM_SYNC carry up to three bi-directional channels of voice data, each at 
8ksamples/s. The format of the PCM samples can be 8-bit A-law, 8-bit µ-law, 13-bit linear or 16-bit linear. The 
PCM_CLK and PCM_SYNC terminals can be configured as inputs or outputs, depending on whether the module is 
the Master or Slave of the PCM interface.   

In applications where the PCM master cannot supply a clock signal, the module can be configured to generate a 
clock signal on this GPIO: PCM_SLVCLK.  Please contact an Ezurio FAE for further details. 

The Module is compatible with the Motorola SSI TM interface and interfaces directly to PCM audio devices 
including the following:  

6.1.3.1

 

Compatible Codec Chips 

 

Qualcomm MSM 3000 series and MSM 5000 series CDMA baseband devices  

 

OKI MSM7705 four channel A-law and µ-law CODEC 

 

Motorola MC145481 8-bit A-law and µ-law CODEC 

 

Motorola MC145483 13-bit linear CODEC 

Summary of Contents for BISMS02BI-01


























Reviews: