Ezurio BISMS02BI-01 Manual Download Page 24

 

www.ezurio.com 

DSH_BT024-00200_1v4 © Ezurio  Ltd 2006 

24 

13.5

 

Ordering Information 

 

The  Embedded  Intelligent  Serial  Module  is  available  with  different  variants  of  production  firmware.    Ordering 
information is provided below: 

 

Part Number 

Description 

TRBLU024-02

 

Embedded Module with integrated ceramic antenna 
and standard AT firmware 

 

 

14.

 

Related Documents 

The  firmware  incorporated  into  the  Embedded  Intelligent  Bluetotoh  Module  is  the  same  as  that  for  the  BISM2 
Module.    All  of  the  firmware  documentation  and  application  data  for  the  BISM2  module  can  be  used  for  this 
module. 

 

blu2i AT Command Set Reference Manual 

 

blu2i Firmware Release Notes  

 

blu2i Multipoint Firmware Reference Manual 

 

Intelligent 

Bluetooth

 Serial Module - Quick Start Guide 

 

Intelligent 

Bluetooth

 Serial Module - FAQ 

 

blu2i Application Scenarios 

 

Bluetooth

 Core 2.0 Specification – 

www.

Bluetooth

.org

 

 

15.

 

Disclaimers 

EZURIO’S 

BLUETOOTH

 PRODUCTS ARE NOT AUTHORISED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT 

DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE MANAGING DIRECTOR OF EZURIO 
LTD. 

The definitions used herein are: 

a) Life support devices or systems are devices which (1) are intended for  surgical  implant  into  the  body,  or  (2) 
support  or  sustain  life  and  whose  failure  to  perform  when  properly  used  in  accordance  with  the  instructions  for 
use provided in the labelling can reasonably be expected to result in a significant injury to the user. 

b)  A  critical  component  is  any  component  of  a  life  support  device  or  system  whose  failure  to  perform  can  be 
reasonably  expected  to  cause  the  failure  of  the  life  support  device  or  system,  or  to  affect  its  safety  or 
effectiveness. 

Ezurio  does  not  assume  responsibility  for  use  of  any  of  the  circuitry  described,  no  circuit  patent  licenses  are 
implied and Ezurio reserves the right at any time to change without notice said circuitry and specifications. 

15.1

 

Data Sheet Status 

This data sheet contains data from the Preliminary specification.  Supplementary data will be published at a later 
date.  Ezurio Ltd reserve the right to change the specification without notice in order to improve the design and 
supply the best possible product. 

Please check with Ezurio Ltd for the most recent data before initiating or completing a design. 

Summary of Contents for BISMS02BI-01


























Reviews: