EZ FX Skinny Jib User Manual Download Page 6

5. Push  the Center Pivot Bolt through 
the Beam to the other side of the Center 
Post.  Use the wide space for easy bolt 
alignment.  

8.  Slide the Camera End Beam over 
the expansion joint.  Use the T Handles 
Hex tool to expand the expansion joint 
and create a firm connection. 

3. Remove the Center Pivot bolt from 
the center post by unscrewing the soft 
grip knob on the end.     

6.  Re-Attach the soft grip knob and slide 
the assembly down into the slotted track to 
the Center Pivot point of the Center Post.    

9. Connect the male end of  the 2’ 
Para Beam to the center post. Use 
the Hex tool to screw the para beam 
set screw and secure it  into place.    
 
 

4.  Place the 2’ Tail Beam thru the  
hallow middle of the center post. Po-
sition it so that the holes on the 
beam’s edge are facing upward.    

7a.  Press the release button and pull the 
expansion joint from the 2’ Tail Beam un-
til the button clicks into place.  

 

7b.   Remove Camera End Beam from 
carry case.      

Vid Remove the Center Pivot 
bolt from the center post.   

 

 

PIC/ VID 

 

PIC/ VID 

 

PIC/ VID 

 

PIC/ VID 

 

PIC/ VID 

 

10.  Connect the Turnbuckle on the 
Camera Platform beam to the female 
end of the Para Beam using the Hex 
tool and set screw.  

NOTE:  Be sure the tip of the set 
screw goes thru the bottom hole of the 
Para Beam to form a secure connec-
tion.  You should feel it protrude thru 
the bottom of the beam. 
 
Be sure to check this on both ends of 
the para beam. 

Skinny Jib SETUP INSTRUCTIONS  - 2’ Configuration 

STOP/ NOTE: The Skinny Jib can be used at 2’ or 4’ Configuration.      

Below are the instructions for the 2’ Configuration.    (Pages 5, 6 & 7) 

Refer to pages 8, 9 and 10 for instructions on the 4’ configuration  

Summary of Contents for Skinny Jib












Reviews: