background image

 

8

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the 

Extron Safety and Regulatory Compliance Guide

 on the Extron website.

 © 2018 Extron Electronics — All rights reserved.  

www.extron.com

 

All trademarks mentioned are the property of their respective owners.

TLP Pro 725C Series • Setup Guide (Continued)

Base Panel Features

e

e

LAN / PoE

275 mA

USB

RESET

MENU

D

D E

E

A

AB

BC

C

Figure 11. 

TLP Pro 725C Base Panel

A

 

LAN/PoE port

   — The TLP Pro 725C must be powered through this port (see 

Step 9 — Connecting the TLP Pro 725C

 on the 

previous page for details)

.

B

 

USB port

 — Compatible with USB 2.0.

C

 

Reset LED

 — Provides feedback about the reset status when the user presses the 

Reset

 button (see “Reset Modes: a Brief 

Summary”).

D

 

Reset button

 — Pressing the 

Reset

 button allows the unit to be reset in any of three different modes (for an overview, see 

“Reset Modes: a Brief Summary”).

E

 

Menu button

 — Pressing the 

Menu

 button activates the setup menu (see “Setup Menu”).

Reset Modes: a Brief Summary

These touchpanels provide the following reset modes (see the 

TLP Pro 725C Series User Guide

 for complete information):

• 

Use Factory Firmware

 — With the unit powered off, press and hold the 

Reset

 button (see figure 11, 

D

) while reapplying power 

to the unit. Use this mode with Toolbelt software to replace firmware in the event of conflicts arising from uploading a firmware 
update.

• 

Reset All IP Settings

 — Press and hold the 

Reset

 button for 6 seconds. After the Reset LED (

C

) flashes twice, release and 

momentarily press the 

Reset

 button. Use this mode to reset all network settings without affecting user-loaded files.

• 

Reset to Factory Defaults

 — Press and hold the 

Reset

 button for 9 seconds. After the Reset LED flashes three times, release 

and momentarily press the 

Reset

 button. Use this mode to return the touchpanel to factory default settings.

• 

Enable or Disable the DHCP Client

 — This mode toggles between DHCP enabled and DHCP disabled.

figure 11

Setup Menu

Press the 

Menu

 button (figure 11, 

E

) to open the 

setup menu. Figure 12 shows the 

Status

 screen. 

Select any of the five available screens (

Status

Network

Display

Audio

, and 

Advanced

) by 

pressing the appropriate button in the navigation bar 
at the top of the screen (for more information, see the 

TLP Pro 725C Series User Guide

).

Status

Display

Audio

Advanced

Exit

Network

Info

Model:

TLP Pro 725C

Part Number: 60-1564-02
Firmware

Version:

1.02.0001-b001

Network

IP Address:
DHCP:
Host Name:

Off

192.168.254.251

TLP-AB-CD-EF

Display

Resolution:
GUI Project:
Sleep Timer:

1024x600
N/A
5 Minutes

Audio

Master Volume:
Master Mute:

Off

99

Advanced

Controller IP:

N/A

Project Size:

N/A

Bootloader

Version:

1.03.0000

Figure 12. 

Setup Menu: Status Screen

68-3319-50 Rev. A

09 18

Summary of Contents for TouchLink TLP Pro 725C Series









Reviews: