1
IMPO
RTAN
T:
IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
FOX3 SR 201 • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX3 SR 201 Fiber Optic
scaling receivers. This scaling receiver scales resolutions up to 4K @ 60 Hz, 4:4:4 video, and extends with 2-CH audio, RS-232,
and IR over fiber. The FOX3 SR 201 is available in either singlemode (SM) or multimode (MM) transmission mode.
WARNING:
The FOX3 SR 201 outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use
with caution. Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.
CLASS 1 LASER PRODUCT
, see the
FOX3 SR 201 User Guide
, at
www.extron.com
.
AVERTISSEMENT :
Le FOX3 SR 201 émet une lumière invisible en continu (conforme à la classe 1) qui peut être
dangereux pour les yeux, à utiliser avec précaution. Associez les bouchons anti-poussière à l’ensemble émetteur/récepteur
optique lorsque le câble fibre optique est débranché.
Produit laser de classe 1
, voir le
FOX3 SR 201 User Guide
sur
www.extron.com
(en anglais)
.
Installation
RS-232
REMOTE
POWER
12V
2.0 A MAX
Tx Rx G
A
OUT IN
B
OUT IN
LAN
RS-232
Tx Rx
Tx Rx
G
IR
HDMI
FOX3 SR 201
R
AUDIO
CONTROL
OUTPUTS
I
I
I
G
G
G
F
F
F
C
C
C
A
A
A
D
D
D
H
H
H
E
E
E
B
B
B
Figure 1.
FOX3 SR 201 Rear Panel
Power Inlet
Remote RS-232
Power LED
LAN Ethernet port
C
Audio output
SFP module and LEDs
D
HDMI output
Reset button
Control RS-232/IR port
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the scaling receiver as required. For mounting details and
considerations, see the
FOX3 SR 201 User Guide
at
Step 2 — Output Connections
a.
Connect an HDMI display to the HDMI output (see figure 1 ,
D
).
b.
Connect an audio output device to the Audio 5-pole captive screw port (
C
) (see figure 2 to wire the captive screw
connector).
Unbalanced Stereo Output
Balanced Stereo Output
Unbalanced Stereo Input
Balanced Stereo Input
Do not tin the wires!
Tip
No Ground Here
No Ground Here
Tip
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves
Tip
Sleeve
Sleeve
Tip
LR
Figure 2.
Audio Wiring Diagrams
ATTENTION:
•
For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (–)
contacts.
•
Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux
contacts négatifs (–).
Step 3 — Control Connections
a.
To pass serial, IR data, or control signals, such as for serial control of a projector,
connect the master device to the transmitter and the controlled device to the
receiver via the CONTROL 5-pole captive screw connector (see
and figure 3 for
wiring).
NOTE:
For returned RS-232 and IR responses (from the scaling receiver to the
transmitter) install the receiver-Tx-to-transmitter-Rx fiber cable in
Tx
Rx
Rx
Tx
Gnd
Gnd
IR Device
RS-232 Device
Rx
Tx
Rx
Tx
G
RS-232
IR
CONTROL
Figure 3.
RS-232 and IR Wiring
1
2
3
