background image

 

7

Step 8: Mounting the ACP 105 EU/MK

Prior to mounting:

1. 

Feed all device cables through the wall or furniture.

NOTE:

  If the unit is not installed in a mud ring, the plastic spacer must be installed. The spacer positions the unit to allow 

the plastic faceplate to attach properly and securely.

2. 

Ensure the cables are connected to the ACP 105 EU/MK rear panel.

Mounting ACP 105 EU or ACP 105 MK Units to an Electrical Wall Box

NOTES:

• 

The electrical wall box is not provided and must be purchased separately.

• 

Install the electrical wall box by following the instructions provided by the manufacturer.

• 

Use the metal mounting bracket provided with the ACP unit. ACP 105 EU and ACP 105 MK metal mounting brackets 
are not interchangeable.

To mount an ACP 105 EU/MK:

1. 

Decide where the panel will be located. Take into 
consideration the position of wall studs and windows that 
could obstruct cable runs.

2. 

Install the electrical wall box by following the instructions 
provided by the manufacturer (see 

1

 in the figure to the right).

NOTES:

• 

The metal mounting brackets provided with the 
EU and MK models are different and are not 
interchangeable.

• 

Ensure the bracket is in the correct orientation 
with the side marked “Front” facing away from 
the wall.

• 

The EU model is attached with screws at the 
top and bottom.

• 

The MK model is attached with screws on both 
sides.

3. 

Disconnect power from all devices at the source and run cables 
through the hole in the wall. Pass them through the metal 
mounting bracket and plastic faceplate to connect them to the 
rear panel captive screw connectors.

4. 

Set the DIP switches to give the panel a unique ID number.

5. 

Insert the ACP 105 EU/MK into the plastic faceplate (

3

) and 

press the entire assembly into the metal mounting bracket (

2

). 

The device is secured to the metal mounting bracket by two 
catches (on each side) that hold the wallplate in place.

SOUR

CE

 5

SOUR

CE

 4

SOUR

CE

 3

SOUR

CE

 2

SOUR

CE

 1

Wall Box

Plastic 
Faceplate

Metal Mounting
Bracket

ACP 105 EU

1

1

3

3

2

2

1

1

2

2

3

3

MK Wall Box

Wall

Metal Mounting
Bracket

Plastic 
Faceplate

ACP 105 MK

MIC

PROGRAM

X

SOURCE 5

SOURCE 4

SOURCE 3

SOURCE 2

SOURCE 1

Summary of Contents for ACP 105 EU/MK









Reviews: