background image

 

 

2.1 “MODE”: mode selection key, in stop position, cyclical select (P1-P25-P1). 

2.2 “SELECT”: SET KEY, in manual position, cyclical select countdown time, countdown distance, countdown 

calorie workout mode, under every mode set workout time. 

2.5 “STOP”: Stop key, in running position press to pause, in setting mode press to standby position; 

2.6 “START”: Start key, in stop position press to start. 

2.7 “ON/OFF FAN”: fan on/off key. 

2.8 “ON/OFF MP3” MP3 on/off key. 

2.9 SPEED “+”

Speed increase key, in workout position, every press increase 0.1KM/H, long pressing make 

continuous increase; 

2.10 SPEED “-“: Speed decline key, in workout position, every press decrease 0.1KM/H, long pressing make 

continuous decline; 

2.11 “QUICK SPEED”: 7 speed fast key, in workout position, select 2

4

6

8

10

12

14 

2.12 INCLINE “+”: In workout position, incline increase key, long pressing make continuous increase; 

2.13 INCLINE “-“: In workout position, incline decrease key, long pressing make continuous decrease; 

2.14 “QUICK INCLINE”: 7 incline fast key, in workout position, select 0

4

6

8

10

12

14 

 

III. Manual training mode instruction operation instruction

 

3.1 Countdown training mode: in standby, press“SELECT”key, enter time countdown setting mode; press 

“SELECT”again, enter distance countdown setting mode; press “ENTER”key, enter calorie countdown       

setting mode. 

 

3.2 Time countdown training mode

in standby, press

SELECT

key, enter setting position, time window blink, 

default value is 30

00,press SPEED+

- key to change the value, range

1--99minutes. Press 

START

key to start treadmill, start from 1KM/H, can press SPEED+

- to adjust the speed. Time countdown to 00

00, treadmill stop; 

 

3.3 Distance countdown training mode: in standby, press

SELECT

key twice to enter setting position, distance 

window blink , default value is 1.0KM/H, press SPEED+

- key to change the value, range

1.00--9.0KM. 

Press 

START

  key to start treadmill, speed start from 1KM/H, can press SPEED+

- to adjust speed. 

Treadmill stop when distance countdown to 0.0; 

 

3.4 Calorie countdown training mode: in standby ,press “SELECT” key 3 times to enter setting position, calorie 

window blink, default value is 50CAL,press SPEED+

- key to change value, range: 10--990CAL.Press 

“START” key to start treadmill, speed start from 1KM/H, can press SPEED+

- to adjust speed. Treadmill 

stop when countdown calorie is 0. 

 

IV. Engineer mode 1 

 

 Remove safety  key,

 press “MODE” key, put on safety key to enter. Setting method: rear roller 

diameter----minimum speed----maximum speed---incline levels

,press SPEED+ or SPEED-to adjust, press 

SELECT to set next value, setting complete to start speed adjust and test ,press START, start speed adjust and 

test, enter standby after adjust and test. 

           

Summary of Contents for ES660B
















Reviews: