manualshive.com logo in svg

Extraflame NORIS, User Manual

Share
Download
Extraflame NORIS User Manual Download Page 18

1

2

3

4

5

6

1

4

3

2

5

6

18

ENGLISH

General menu

go back - exit 

    scroll parameters: next (3); previous (2)

    

    Change settings data: increase (4); decrease (5)

Confirm - access menu

MODES

SET

VENTILATION

SET

*AIR DUCTING 1

SET

**TEMPERATURE

*AIR DUCTING 2

SET

**TEMPERATURE

*AIR ZONE CONTROL

SET

EASY SETUP

SET

CHRONO

ENABLING

CHRONO MODE

PRG1

SETTINGS

DATE-TIME

PRG2

LANGUAGE

PRG3

 

CHIMNEY FLUE TYPE

PRG4

DISPLAY

STAND-BY

DELTA T

***STOVE STATUS

FIRST LOAD

*PLUs ONLY

**iF a TemPeraTUre PrOBe is CONNeCTeD

***TeCHNiCiaNs ONLY

CLEANING

DEGREES

RESET

*** TECH MENU

EASY CONTROL

General warnInGs

Advice to follow for the first start-ups of the product:

During the first hours of operation, there may be some smoke or 

odours, but they are due to the normal “thermal break-in” process.

During this process, the duration of which changes depending on the 

product, it is recommended to:

 

Š

Ventilate the room well

 

Š

if present, remove any majolica or natural stone parts from the 

top part of the product

 

Š

activate the product at the maximum power and temperature

 

Š

avoid remaining in the room for a long time

 

Š

Do not touch the surfaces of the product

Notes: 

The process is completed after a few heating/cooling cycles.

For combustion, do not use elements or substances other than those 

indicated in the manual.

Before turning on the product, it is necessary to perform the 

following checks:

 

Š

if it is intended to be connected to a hydraulic system, it must 

be complete and fully functional and in compliance with the 

instructions given in the product manual and with the relevant 

regulations in force.

 

Š

The pellet hopper must be fully loaded

 

Š

The combustion chamber and the burn pot must be clean

 

Š

make sure that the fire holder, the ash drawer and the pellet 

hopper close hermetically (if present in the hermetic version); they 

must be closed and there must be no foreign bodies in the sealing 

elements and gaskets.

 

Š

Check that the power cord is properly connected

 

Š

The switch (if present) must be set to position “1”.

Summary of Contents for NORIS









































Reviews:

No comments

Brands by name

Popular brands

Load more brands