background image

 

13

Warranty 

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects 
in parts and workmanship for one year from date of shipment (a six month limited 
warranty applies on sensors and cables). If it should become necessary to return the 
instrument for service during or beyond the warranty period, contact the Customer 
Service Department at (781) 890-7440 ext. 210 for authorization or visit our website at 
www.extech.com  (click on ‘Contact Extech’ and go to ‘Service Department’ to request an 
RA number). A Return Authorization (RA) number must be issued before any product is 
returned to Extech. The sender is responsible for shipping charges, freight, insurance 
and proper packaging to prevent damage in transit. This warranty does not apply to 
defects resulting from action of the user such as misuse, improper wiring, operation 
outside of specification, improper maintenance or repair, or unauthorized modification. 
Extech specifically disclaims any implied warranties or merchantability or fitness for a 
specific purpose and will not be liable for any direct, indirect, incidental or consequential 
damages. Extech's total liability is limited to repair or replacement of the product. The 
warranty set forth above is inclusive and no other warranty, whether written or oral, is 
expressed or implied. 

Calibration and Repair Services 

Extech offers complete repair and calibration services for all of the 
products we sell. For periodic calibration, NIST certification or repair of any 
Extech product, call customer service for details on services available. 
Extech recommends that calibration be performed on an annual basis to 
insure calibration integrity.

 

 
 
 
 
 
 
 

 

 
 

 

Copyright 

©

 2002 Extech Instruments Corporation. 

All rights reserved including the right of reproduction 

in whole or in part in any form.

 

 

MN26    V1.3   6/02 

 

Tech Support Hotlines 

781-890-7440 ext. 200     

[email protected]

     www.extech.com 

Summary of Contents for MiniTec Series














Reviews: