Exmark OCD01 Operator'S & Parts Manual Download Page 10 | Manualshive

Page: 10 / 28

background image

6

3.2.5 Install the cable bracket (item 1) by the foot pedal and leave the hardware loose. Use

the correct mounting holes as shown in Figure 5A.

FIGURE

5A

FIGURE

5B

3.2.6 Install cable. Make sure the nuts are centered as shown in Figure 6.

FIGURE 6

3.2.7 Remove the belt cover near the discharge opening.

3.2.8 Route the cable over the left side of the cross-shaft. Remove the seal and run the nuts

off the cable. Feed the parts loosely through one hole of the cable hanger strap. Hang
the cable under the right side of the cross-shaft and fasten with cable hanger strap as
shown in Figure 7. Reinstall nuts and seal.

«
...
8
9
10
11
12
...
»

Summary of Contents for OCD01





























Reviews:

No comments

Related manuals for OCD01

Brand: AA Products Pages: 8

Brand: Camcar Pages: 6

Brand: H&S Pages: 96

Brand: PASCO Pages: 5

Brand: PASCO Pages: 4

Brand: PASCO Pages: 8

Brand: PASCO Pages: 4

Brand: PASCO Pages: 12

Brand: PASCO Pages: 5

Brand: PASCO Pages: 3

Brand: Obelink Pages: 2

Brand: S+S Regeltechnik Pages: 16

Brand: Alpha Arsenal Pages: 15

Brand: Suunto Pages: 5

Brand: Cerlic Pages: 20

Brand: EUFAB Pages: 12

Brand: Fisher-Price Pages: 12

Brand: Oasis Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands