background image

 

19 

 

TROUBLESHOOTING & MAINTENANCE

 

 

TROUBLE SHOOTING 

1. 

PROBLEM: 

The bike wobbles when in use. 

1)  SOLUTION:

 Turn the 

Adjustable Levelers (10)

 on the 

Front and Rear Stabilizer (2) & (3) 

or as needed to level the bike. 

2. 

PROBLEM: 

The bike makes a squeaking noise when in use. 

1)  SOLUTION: 

The bolts may be loose on the recumbent bike. Inspect all of the bolts and 

tighten any loose bolts. 

3. 

PROBLEM: 

The console won

’t pair with the device. 

PROBLEM: 

The App disconnects. 

1)  SOLUTION: Replace batteries with 2 fresh AAA batteries. 

MAINTENANCE 

1.  The bike can be cleaned with a soft clean damp cloth.     
2. 

DO NOT

 use abrasives or solvents on the plastic parts.     

3.  Wipe your perspiration off the bike after each use.     
4.  Be careful not to get excessive moisture on the Console as this might cause an electrical hazard or 

the electronics to fail. 

5.  Keep the bike, especially the computer console out of direct sunlight to prevent damage.   
6.  Be sure all assembly bolts, nuts, screws, and pedals on the machine are thoroughly tightened prior 

to use. Tighten any loose parts. 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
Transporting the Bike

 

 
Pull the 

Handlebar (7) 

with both hands until the 

Wheels (35)

 on the 

Front Stabilizer (2)

 make 

contact with the ground. Pull or Push the Bike to the desired storage area before gently 
lowering the Bike. Always maintain both hands on the Bike during transportation. 

 

Storage 

Store the bike in a clean and dry environment away from pets and children.

 

 

Summary of Contents for Momentum Bike
























Reviews: