exemys GRD-MQ Series User Manual Download Page 60

Page: 60 / 85

GETI

Reads all

channels (Max. 50 channels in on SMS).

Digital Outputs:

Command

Description

GETO

[O channel]

Reads channel O.

(Read note*)

GETO

[first O channel]…[last

O channel]

Read several O channels

GETO

Reads all O channels (Max. 50 channels in on SMS).

Analog Inputs:

Command

Description

GETAN

[AN channel]

Reads channel

(Read note*)

GETAN

[first AN channel]

…[last AN channel]

Read several

channels

GETAN

Reads all

channels (Max. 15 channels in on SMS).

Pulse Inputs:

Command

Description

GETPI

[PI channel]

Reads channel

GETPI

[first PI channel]…[last

PI channel]

Read several

channels

GETPI

Reads all

channels (Max. 15 channels in on SMS).

If you receive three point (...) ending the SMS, it means that more information will be sent on another
SMS.

*Note

: If you configured an SMS alarm for this channel you will receive the full text you configured. The

text will change depending on the state of the I/O. Please read SMS alarms section for further
information.

Setting outputs and pulses

You can set an output or pulse channel by sending an SMS to the GRD.

This commands can only be sent from the phone numbers added to the GRD-MQ
"Phone book". Please read SMS alarms section for further information.

Command

Description

SETO

[O channel] [state]

The O channel will be set to "state"

GRD-MQ User Manual

SMS Monitoring and Configuration

59 / 84

Summary of Contents for GRD-MQ Series






















































































Search results

Summary of Contents for GRD-MQ Series

Reviews:

Related manuals for GRD-MQ Series

Brands by name

Popular brands

exemys GRD-MQ Series, User Manual

Search results

Summary of Contents for GRD-MQ Series

Reviews:

Related manuals for GRD-MQ Series

Brands by name

Popular brands