manualshive.com logo in svg

exemys GRD-MQ Series, User Manual, Page: 57 / 85

Share
Download
exemys GRD-MQ Series User Manual Download Page 57

STATE o ?

Returns the status of GRDs communications

Note: This command does not require a password.

Returns the current configuration

Command

Description

LIST

Returns the basic equipment configuration, the model and serial
number.

Example of a response:

MODEL: GRD3625-MQ-3G / SN: 124 / GPRS: apn/user/password

Note: This command does not require a password.

Signal level

Command

Description

SIGNAL

Signal level

The signal level can vary between -113 dbm and -51 dbm

Note: This command does not require a password.

Versions and IMEI

Command

Description

VERSION

Returns the versions of Hardware, Software and IMEI

Example of a response:

FIRbrokerARE: 1.0 HARDWARE: 1.0 IMEI 123456789123456

Note: This command does not require a password.

GRD-MQ configuration

Modify GPRS parameters

Using this command you can configure the apn, user and password of the GPRS. This command will
also enable GPRS if it was disabled

Command

Description

GPRS apn user password 

[password]

Configures the GPRS service

GRD-MQ User Manual

SMS Monitoring and Configuration 

56 / 84

Summary of Contents for GRD-MQ Series






















































































Reviews:

No comments