Exegin Q53 Installation And Configuration Manual Download Page 15 | Manualshive

Page: 15 / 84

background image

17

Q53 Installation and Configuration Guide © Exegin Technologies Limited, 2009

iii. Installing the Q53
Connecting the Q53 to a Network

Two LED indicators are used to indicate Ethernet link integrity (see

LED at the bottom left of the UTP network connector will be illuminated when a 100
MB/S link is established over the network connection, or extinguished otherwise. The
red LED at the bottom right of the UTP network connector will be illuminated when a
10 MB/S link is established over the network connection, or extinguished otherwise.

Figure 3—Q53 Top View: LED Status Indicators

Watch the LED indicators on the top panel as they cycle through the power-on self-test.
When the test is complete, the STAT LED will flash once per second or, if there is no IP
address configured, twice per second (see

on page 19 for instruction on how to

configure an IP address).

«
...
13
14
15
16
17
...
»

Summary of Contents for Q53





















































































Reviews:

No comments

Related manuals for Q53

Brand: 2N Pages: 2

Brand: KE2 Pages: 16

Brand: 2Wire Pages: 14

Brand: Icom Pages: 2

Brand: Icom Pages: 326

Brand: TRENDnet Pages: 4

Brand: auto maskin Pages: 13

Brand: Duemmegi Pages: 11

STHC-ISG02DB-WS433-CL-04

Brand: daviteq Pages: 25

Brand: Aaeon Pages: 26

Brand: SSS Siedle Pages: 28

Brand: Nokia Pages: 3

CC500 - VPN - Gateway

Brand: Nokia Pages: 11

Brand: Nokia Pages: 48

Brand: Nokia Pages: 58

Brand: Nokia Pages: 62

Brand: Nokia Pages: 72

Brand: Nokia Pages: 87

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands