Exegin Q53 Installation And Configuration Manual Download Page 63

Page: 63 / 84

Q53 Installation and Configuration Guide © Exegin Technologies Limited, 2009

viii. Reference Information
Complete Command Reference

load [default]

Load the settings stored in Flash and use
them as the current or working settings. If

default

is specified as well, factory

settings will be loaded. Use this after power
failure to restore settings saved in Flash.

netstat

Display current network status, including
TCP packet statistics and the current state of
each TCP and UDP socket in the system.

ping [-s] hostIPaddress

[datasize [packetnumber]]

ping

" another TCP/IP host, specified by

hostIPaddress

, on the network.

datasize

the datagram packet size which defaults to
64 bytes if no size is included in the syntax
and

packetnumber

is the number of requests

to be sent.

To use a host or IP name instead of the
address, you must have set the DNS server
on the Q53. Use the command "

set

sysinfo dns...

" to do this.

For example:

ping 192.168.11.30

quit

Close the telnet command session.

restart

Perform a warm boot or hardware reset
simulating a power-on reset. This will
restore current settings to those stored in
Flash as the Flash settings will be read and
loaded into memory upon bootup.

save [default]

Save the current settings to Flash so they are
remembered after power cycles. Sysinfo,
snmp, user, and sntp settings will be saved.
If

default

is specified as well, factory

settings will be saved to Flash overwriting
any new settings you have configured.
Resetting the unit is not required.

Table 7—Miscellaneous Commands

Command Syntax

Description

Summary of Contents for Q53





















































































Search results

Summary of Contents for Q53

Reviews:

Related manuals for Q53

Brands by name

Popular brands

Exegin Q53, Installation And Configuration Manual

Search results

Summary of Contents for Q53

Reviews:

Related manuals for Q53

Brands by name

Popular brands